To Captain Neal
 

As I understand it from this newsgroup, you have an identical coronado to
mine, except, I think you have a shoal keel and I do not. Apart from this
difference, I believe they are more or less identical, though i suspectthat
you have updated your interior as your's is a live aboard vessel. I am
currently in the middle of a refit and would appreciate your advice.

My first concern is the actual eorking infrastructure, I need to replace or
repair the water tank and the water fixtures. Is your tank (or was it
originally) only fillable from inside the boat under the aft seat? if so,
did you refit this item? Did you replace your water fixtures in the head
and galley? if so, how did you pulmb them? Did you fit a sea-water pump,
if so, how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station above
the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be
able to swing into the companionway while underway. How are your
instruments fit? Do you have an outboard, or one of Coronado's old
saildrive motors. What is your maximum speed underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

Sorry I did not answer your post the first time, Dave.

I thought you were a Bertie the Bunyip sock puppet.

Have you visited my website?

There are lots of pictures there that might help you with your
conversions.

http://captneal.homestead.com/index.html

Just follow the links to the interior where you will see all the modifications
I have made.

I raised the dinette and put a fill in the water tank on the side of the
raised area. I also put another 18-gallon water tank under the center
of the cockpit between the two large stringers.

I used hand pumps for water both in the head and the galley and have
put tubing with a tee and a valve so I can draw water from either tank
from either sink. I put a cockpit fill (little perfections page) in for
the under cockpit tank but still have to fill the settee tank from inside
the vessel though it is on the side of the settee now so I don't have
to move the cushion. I also got rid of the old, rotten wooden top for
the tank and replaced it with plastic - Star Board.


I got rid of the door to the head and reversed the hanging locker door
so it would open against the mast post. It gives a bit of privacy for the
head this way

The swinging instrument board works well. I now have an outside depth sounder
which makes the use of the board optional.

I use a 9.9 Honda Four which powers the boat to hull speed at about
half throttle in mild conditions. It gets great gas mileage and is very
quiet. It is on the transom in the factory cut-out.

Feel free to ask more questions here as there are many more
people here who could profit from discussing boats for once.

CN


"Sailing Dave" wrote in message rver.com...
As I understand it from this newsgroup, you have an identical coronado to
mine, except, I think you have a shoal keel and I do not. Apart from this
difference, I believe they are more or less identical, though i suspectthat
you have updated your interior as your's is a live aboard vessel. I am
currently in the middle of a refit and would appreciate your advice.

My first concern is the actual eorking infrastructure, I need to replace or
repair the water tank and the water fixtures. Is your tank (or was it
originally) only fillable from inside the boat under the aft seat? if so,
did you refit this item? Did you replace your water fixtures in the head
and galley? if so, how did you pulmb them? Did you fit a sea-water pump,
if so, how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station above
the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be
able to swing into the companionway while underway. How are your
instruments fit? Do you have an outboard, or one of Coronado's old
saildrive motors. What is your maximum speed underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

Good idea withn the locker door.

Your website says that you can access salt water from the galley sink. How
did you plumb that, or is one of your tanks filled with salt water and, if
so, why?

Did you replace the head?

Did you replace the settee tank itself?

How is your bulkhead fixed to the fiberglass? Is it simply constructed of
marine plywood, or did you glass over the whole thing?

I am planning to do away with the dinette entirely, as I do not really use
it anyway and the lack of floor space under the portside seat is maddening.
I am planning to make a sofa pit out of that side with a conversion kit to
turn the entire space into a bed (for me and wife and the kids up in the
berth) Any experience with this arrangement?

Have you covered the glass ceiling and walls with any sort of fabric at all?

BTW, you have a fine looking vessel. have you sailed it far? I have done
Duluth to Quebec in two years. I plan a complete tour of the Great Lakes
this summer and a Trans-A the following summer Cleveland to Cleveland,
England.

dave





"Capt. Neal®" wrote in message
...
Sorry I did not answer your post the first time, Dave.

I thought you were a Bertie the Bunyip sock puppet.

Have you visited my website?

There are lots of pictures there that might help you with your
conversions.
http://captneal.homestead.com/index.html

Just follow the links to the interior where you will see all the
modifications
I have made.
I raised the dinette and put a fill in the water tank on the side of the
raised area. I also put another 18-gallon water tank under the center
of the cockpit between the two large stringers.
I used hand pumps for water both in the head and the galley and have
put tubing with a tee and a valve so I can draw water from either tank
from either sink. I put a cockpit fill (little perfections page) in for
the under cockpit tank but still have to fill the settee tank from inside
the vessel though it is on the side of the settee now so I don't have
to move the cushion. I also got rid of the old, rotten wooden top for
the tank and replaced it with plastic - Star Board.


I got rid of the door to the head and reversed the hanging locker door
so it would open against the mast post. It gives a bit of privacy for the
head this way

The swinging instrument board works well. I now have an outside depth
sounder
which makes the use of the board optional.

I use a 9.9 Honda Four which powers the boat to hull speed at about
half throttle in mild conditions. It gets great gas mileage and is very
quiet. It is on the transom in the factory cut-out.

Feel free to ask more questions here as there are many more
people here who could profit from discussing boats for once.

CN


"Sailing Dave" wrote in message
rver.com...
As I understand it from this newsgroup, you have an identical coronado to
mine, except, I think you have a shoal keel and I do not. Apart from
this difference, I believe they are more or less identical, though i
suspectthat you have updated your interior as your's is a live aboard
vessel. I am currently in the middle of a refit and would appreciate
your advice.

My first concern is the actual eorking infrastructure, I need to replace
or repair the water tank and the water fixtures. Is your tank (or was it
originally) only fillable from inside the boat under the aft seat? if
so, did you refit this item? Did you replace your water fixtures in the
head and galley? if so, how did you pulmb them? Did you fit a sea-water
pump, if so, how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station above
the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be
able to swing into the companionway while underway. How are your
instruments fit? Do you have an outboard, or one of Coronado's old
saildrive motors. What is your maximum speed underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

What sort of weather have you weathered with the Mustard? largest seas I
have seen was 14 footers on Erie and 45 knot winds. The boat didn't mind as
much as I did. I truly didn't think we were coming back. The engine was a
joke and the waves pounded us without mercy. Took on water to the top of
the settee seats. BAD TIME.
"Capt. Neal®" wrote in message
...
Sorry I did not answer your post the first time, Dave.

I thought you were a Bertie the Bunyip sock puppet.

Have you visited my website?

There are lots of pictures there that might help you with your
conversions.
http://captneal.homestead.com/index.html

Just follow the links to the interior where you will see all the
modifications
I have made.
I raised the dinette and put a fill in the water tank on the side of the
raised area. I also put another 18-gallon water tank under the center
of the cockpit between the two large stringers.
I used hand pumps for water both in the head and the galley and have
put tubing with a tee and a valve so I can draw water from either tank
from either sink. I put a cockpit fill (little perfections page) in for
the under cockpit tank but still have to fill the settee tank from inside
the vessel though it is on the side of the settee now so I don't have
to move the cushion. I also got rid of the old, rotten wooden top for
the tank and replaced it with plastic - Star Board.


I got rid of the door to the head and reversed the hanging locker door
so it would open against the mast post. It gives a bit of privacy for the
head this way

The swinging instrument board works well. I now have an outside depth
sounder
which makes the use of the board optional.

I use a 9.9 Honda Four which powers the boat to hull speed at about
half throttle in mild conditions. It gets great gas mileage and is very
quiet. It is on the transom in the factory cut-out.

Feel free to ask more questions here as there are many more
people here who could profit from discussing boats for once.

CN


"Sailing Dave" wrote in message
rver.com...
As I understand it from this newsgroup, you have an identical coronado to
mine, except, I think you have a shoal keel and I do not. Apart from
this difference, I believe they are more or less identical, though i
suspectthat you have updated your interior as your's is a live aboard
vessel. I am currently in the middle of a refit and would appreciate
your advice.

My first concern is the actual eorking infrastructure, I need to replace
or repair the water tank and the water fixtures. Is your tank (or was it
originally) only fillable from inside the boat under the aft seat? if
so, did you refit this item? Did you replace your water fixtures in the
head and galley? if so, how did you pulmb them? Did you fit a sea-water
pump, if so, how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station above
the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be
able to swing into the companionway while underway. How are your
instruments fit? Do you have an outboard, or one of Coronado's old
saildrive motors. What is your maximum speed underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

What sort of weather have you weathered with the Mustard? largest seas I
have seen was 14 footers on Erie and 45 knot winds. The boat didn't mind as
much as I did. I truly didn't think we were coming back. The engine was a
joke and the waves pounded us without mercy. Took on water to the top of
the settee seats. BAD TIME.


"Sailing Dave" wrote in message
rver.com...
Good idea withn the locker door.

Your website says that you can access salt water from the galley sink.
How did you plumb that, or is one of your tanks filled with salt water
and, if so, why?

Did you replace the head?

Did you replace the settee tank itself?

How is your bulkhead fixed to the fiberglass? Is it simply constructed of
marine plywood, or did you glass over the whole thing?

I am planning to do away with the dinette entirely, as I do not really use
it anyway and the lack of floor space under the portside seat is
maddening. I am planning to make a sofa pit out of that side with a
conversion kit to turn the entire space into a bed (for me and wife and
the kids up in the berth) Any experience with this arrangement?

Have you covered the glass ceiling and walls with any sort of fabric at
all?

BTW, you have a fine looking vessel. have you sailed it far? I have done
Duluth to Quebec in two years. I plan a complete tour of the Great Lakes
this summer and a Trans-A the following summer Cleveland to Cleveland,
England.

dave





"Capt. Neal®" wrote in message
...
Sorry I did not answer your post the first time, Dave.

I thought you were a Bertie the Bunyip sock puppet.

Have you visited my website?

There are lots of pictures there that might help you with your
conversions.
http://captneal.homestead.com/index.html

Just follow the links to the interior where you will see all the
modifications
I have made.
I raised the dinette and put a fill in the water tank on the side of the
raised area. I also put another 18-gallon water tank under the center
of the cockpit between the two large stringers.
I used hand pumps for water both in the head and the galley and have
put tubing with a tee and a valve so I can draw water from either tank
from either sink. I put a cockpit fill (little perfections page) in for
the under cockpit tank but still have to fill the settee tank from inside
the vessel though it is on the side of the settee now so I don't have
to move the cushion. I also got rid of the old, rotten wooden top for
the tank and replaced it with plastic - Star Board.


I got rid of the door to the head and reversed the hanging locker door
so it would open against the mast post. It gives a bit of privacy for the
head this way

The swinging instrument board works well. I now have an outside depth
sounder
which makes the use of the board optional.

I use a 9.9 Honda Four which powers the boat to hull speed at about
half throttle in mild conditions. It gets great gas mileage and is very
quiet. It is on the transom in the factory cut-out.

Feel free to ask more questions here as there are many more
people here who could profit from discussing boats for once.

CN


"Sailing Dave" wrote in message
rver.com...
As I understand it from this newsgroup, you have an identical coronado
to mine, except, I think you have a shoal keel and I do not. Apart from
this difference, I believe they are more or less identical, though i
suspectthat you have updated your interior as your's is a live aboard
vessel. I am currently in the middle of a refit and would appreciate
your advice.

My first concern is the actual eorking infrastructure, I need to replace
or repair the water tank and the water fixtures. Is your tank (or was
it originally) only fillable from inside the boat under the aft seat?
if so, did you refit this item? Did you replace your water fixtures in
the head and galley? if so, how did you pulmb them? Did you fit a
sea-water pump, if so, how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station
above the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be
able to swing into the companionway while underway. How are your
instruments fit? Do you have an outboard, or one of Coronado's old
saildrive motors. What is your maximum speed underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

"Sailing Dave" wrote in message rver.com...
Good idea withn the locker door.

Your website says that you can access salt water from the galley sink. How
did you plumb that, or is one of your tanks filled with salt water and, if
so, why?

I put in a 3/4 inch thru-hull in the bottom of the sink locker and have
one of those Whale Galley gusher foot pumps to a spigot near the hand
pump. The foot pump actuator arm is under the bottom companion step.


Did you replace the head?

No, it still has the original head which I rarely use preferring the
cedar bucket method.


Did you replace the settee tank itself?

No, it is GPR and part of the settee structure.


How is your bulkhead fixed to the fiberglass? Is it simply constructed of
marine plywood, or did you glass over the whole thing?

It is marine ply with glossy color-matched formica glued on with rubber cement.
Edges sealed with 5200 against moisture intrusion and rot. Bulkhead glued
in place with 5200 and no mechanical fasteners.

I am planning to do away with the dinette entirely, as I do not really use
it anyway and the lack of floor space under the portside seat is maddening.
I am planning to make a sofa pit out of that side with a conversion kit to
turn the entire space into a bed (for me and wife and the kids up in the
berth) Any experience with this arrangement?

That's how it used to work when the dinette table was lowered onto the
settees. This would be easy to do by just lowering the table into the grooves
in the settees and making some comfy cushions.

Have you covered the glass ceiling and walls with any sort of fabric at all?


Only on what is usually called the ceiling (sides) and I glued carpet there
to minimize sweating as it is not cored in the sides as it is on the overhead.

BTW, you have a fine looking vessel. have you sailed it far? I have done
Duluth to Quebec in two years. I plan a complete tour of the Great Lakes
this summer and a Trans-A the following summer Cleveland to Cleveland,
England.

Yes, we both have fine vessels and they are very seaworthy. I have sailed
mine thousands of miles and have lived aboard for over fifteen years now.
Haven't done a crossing with her yet but may get a wild hair up my arse
one of these days and do so. Coronado 27s are pretty stout.


CN

I've been in some very large seas in the Gulf Stream in several occasions.

Fifteen feet for sure. There have been times when in the tough I could not
see a very large ship a half mile or so off. Had blue water slop into the cockpit
from time to time. Never had a control problem as I have a variety of sails and
use them properly for the wind conditions. Unlike most of the wimps around
here, I am not afraid to go forward to change a headsail when necessary no
matter the conditions. Never had any water in the interior. I keep the bottom
washboard in the companionway when offshore and it goes halfway up the
opening. It is gasketed and watertight even if the cockpit should fill which
it never has.

She used to pound somewhat -hull flexing and hitting interior accommodation
component. Since I poured flotation foam between the hull and liner from
bow to companionway she has become quiet even when pounding into a steep
chop and any oil-canning has been eliminated. She's like a Boston Whaler now.

CN


"Sailing Dave" wrote in message rver.com...
What sort of weather have you weathered with the Mustard? largest seas I have seen was 14 footers on Erie and 45 knot winds. The
boat didn't mind as much as I did. I truly didn't think we were coming back. The engine was a joke and the waves pounded us
without mercy. Took on water to the top of the settee seats. BAD TIME.
"Capt. Neal®" wrote in message ...
Sorry I did not answer your post the first time, Dave.

I thought you were a Bertie the Bunyip sock puppet.

Have you visited my website?

There are lots of pictures there that might help you with your
conversions.
http://captneal.homestead.com/index.html

Just follow the links to the interior where you will see all the modifications
I have made.
I raised the dinette and put a fill in the water tank on the side of the
raised area. I also put another 18-gallon water tank under the center
of the cockpit between the two large stringers.
I used hand pumps for water both in the head and the galley and have
put tubing with a tee and a valve so I can draw water from either tank
from either sink. I put a cockpit fill (little perfections page) in for
the under cockpit tank but still have to fill the settee tank from inside
the vessel though it is on the side of the settee now so I don't have
to move the cushion. I also got rid of the old, rotten wooden top for
the tank and replaced it with plastic - Star Board.


I got rid of the door to the head and reversed the hanging locker door
so it would open against the mast post. It gives a bit of privacy for the
head this way

The swinging instrument board works well. I now have an outside depth sounder
which makes the use of the board optional.

I use a 9.9 Honda Four which powers the boat to hull speed at about
half throttle in mild conditions. It gets great gas mileage and is very
quiet. It is on the transom in the factory cut-out.

Feel free to ask more questions here as there are many more
people here who could profit from discussing boats for once.

CN


"Sailing Dave" wrote in message rver.com...
As I understand it from this newsgroup, you have an identical coronado to mine, except, I think you have a shoal keel and I do
not. Apart from this difference, I believe they are more or less identical, though i suspectthat you have updated your interior
as your's is a live aboard vessel. I am currently in the middle of a refit and would appreciate your advice.

My first concern is the actual eorking infrastructure, I need to replace or repair the water tank and the water fixtures. Is
your tank (or was it originally) only fillable from inside the boat under the aft seat? if so, did you refit this item? Did
you replace your water fixtures in the head and galley? if so, how did you pulmb them? Did you fit a sea-water pump, if so,
how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station above the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be able to swing into the companionway while underway.
How are your instruments fit? Do you have an outboard, or one of Coronado's old saildrive motors. What is your maximum speed
underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

Neal is certainly the right person to ask about this. While he's generally a
**** person, he knows a heck of a lot about his Coronado.

--
"j" ganz @@
www.sailnow.com

"Sailing Dave" wrote in message
rver.com...
As I understand it from this newsgroup, you have an identical coronado to
mine, except, I think you have a shoal keel and I do not. Apart from this
difference, I believe they are more or less identical, though i
suspectthat you have updated your interior as your's is a live aboard
vessel. I am currently in the middle of a refit and would appreciate your
advice.

My first concern is the actual eorking infrastructure, I need to replace
or repair the water tank and the water fixtures. Is your tank (or was it
originally) only fillable from inside the boat under the aft seat? if so,
did you refit this item? Did you replace your water fixtures in the head
and galley? if so, how did you pulmb them? Did you fit a sea-water pump,
if so, how is it plumbed to the outside?

I am getting rid of the door on the head and building a nav station above
the port side galley. Any advice?

I am fitting my nav instruments on a swinging peice of teak that will be
able to swing into the companionway while underway. How are your
instruments fit? Do you have an outboard, or one of Coronado's old
saildrive motors. What is your maximum speed underway with motor only?

So many questions, so little space.

Sailing Dave - The Storm and The Spray

"Sailing Dave" wrote in message
I plan a complete tour of the Great Lakes this summer and a Trans-A the
following summer Cleveland to Cleveland, England.

A Trans Atlantic in a Coronado 27??????

BWAHAHAHAHAHAHAHAHAAAAAA

Good Luck!

CM

"Sailing Dave" wrote in message
rver.com...
What sort of weather have you weathered with the Mustard? largest seas I
have seen was 14 footers on Erie and 45 knot winds. The boat didn't mind
as much as I did. I truly didn't think we were coming back. The engine
was a joke and the waves pounded us without mercy. Took on water to the
top of the settee seats. BAD TIME.

If that's all it took... I'd seriously reconsider the Atlantic Crossing!!

CM