wow, I should've proof read that. lol.
ehh, you'll figure out what I meant to say.
Scout

"Scout" wrote in message
...
I ran a length of 3/8" OD soft copper tubing inside 7/8" copper tubing. I
made a tight set of rows using 7/8" 90 deg copper elbows, so the outside
of
the condenser is squarish. But, this made it extremely difficult to fish
the
3/8 through it. If I were to make another, I would layout a straight
length
of 7/8" soft tubing, then insert a slightly longer length of 3/8" soft
tubing inside the 7/8", then roll the whole thing into as tight a circle
as
possible (no easy task either, but doable).
Solder a 7/8" copper tee on each end. The 3/8" tubing passes through the
tees at both ends, (either bush the 7/8" down to 3/8" or pinch and braze a
short 7/8 stub around the 3/8 for a water tight seal. The third tee
opening
at each end is your fresh water inlet and outlet. I solder hose adapters
on
here and this is where I connect the garden hoses. I put a Taco 007
circulating pump in series with the 7/8 tubing. The other end of both
hoses
connects to a second coil of copper tubing. I used 5/8" her (M, or thin
copper for easier heat transfer). I formed mine into a rough triangle
shape
so it would fit in the anchor locker, around the anchor, when not in use.
If you don't mind making (or buying) a new heat exchanger every year or
so,
you could pump seawater through the exchanger. It does make the job a bit
simpler.
One end of the 3/8" tubing ends connect to the compressor discharge
(outlet)
and the other end becomes attaches to the expansion device (probably a
capillary tube). Be sure to use a filter-drier between the 3/8 and the
capillary tubing.
Best practice is to pull the system into a vacuum before charging it with
refrigerant. I've it done plenty of times though, if you didn't have a
vacuum pump, that you could just purge the system with refrigerant to
displace the air. This works, but there are a few problems with it (e.g.,
it's illegal in the USA to purge refrigerant to the atmosphere, it
shortens
the life of the system by not removing all the moisture and
non-condensable
gases that are surely still present in the system).
I F'd up and let the water sit in mine all winter and of course the water
froze and damaged the tubing. I made it a lesson plan at school though; I
brought it in with my torch, then taught a quick lesson on brazing, and
turned it over to my 10th graders. They learned how to braze and I got my
system working again.
Scout


"Jeff Morris" wrote in message
...
I was curious about your homemade condenser - how did you make it and
did
you
have to vacuum down the system to install it?


"Scout" wrote in message
...
Thom,
AC ranks right up there with indoor plumbing and anti-biotics. No past
king
or queen lived better than we in those regards.
I've spent most of my life in mechanical construction (steamfitter).
It's
all about boiler rooms, city rooftops, and stifling mechanical rooms.
In
the
winter you freeze, in the summer, you sometimes work 'til you puke. On
one
of those hot days I made a vow to myself to be cool and dry when I'm
relaxing. My next sailboat (it's gonna have to wait until I move next
year)
will have a less obtrusive, factory designed unit. Until then this
will
have
to do. ahhhhhhhhhhhhhh
Scout

"Thom Stewart" wrote in message
...
Scout,
I want you tknow that this week I've been very envious of your
set-up.

Ole Thom