Don't forget to sweeten your batteries!
 

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Don't forget to sweeten your batteries!
 

"HK" wrote in message
. ..
Wayne.B wrote:
On Wed, 26 Dec 2007 20:21:41 -0500, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Once a month is overkill in my experience. If the batteries are in
good condition, fully charged at winterization, and totally
disconnected from all loads, they will start right up in the spring.


You do it your way, I'll do it mine. It costs only a couple of pennies to
do it my way.


Thanks for the reminder. Mine has been sitting out in the shed for a couple
months.
I may bring it into the cool basement rather than the freezing shed.

Don't forget to sweeten your batteries!
 

On Wed, 26 Dec 2007 20:21:41 -0500, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Once a month is overkill in my experience. If the batteries are in
good condition, fully charged at winterization, and totally
disconnected from all loads, they will start right up in the spring.

Don't forget to sweeten your batteries!
 

Wayne.B wrote:
On Wed, 26 Dec 2007 20:21:41 -0500, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Once a month is overkill in my experience. If the batteries are in
good condition, fully charged at winterization, and totally
disconnected from all loads, they will start right up in the spring.


You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Don't forget to sweeten your batteries!
 

On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)

Don't forget to sweeten your batteries!
 

Wayne.B wrote:
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)


I don't find it difficult. I simply remove the batteries before
shrinkwrapping and bring them home. That's one of the advantages of
owning boats where critical systems and subsystems are designed for easy
access and maintenance.

Don't forget to sweeten your batteries!
 

That's one of the advantages of
owning boats where critical systems and subsystems are designed for easy
access and maintenance.

A row boat comes to mind....

--Mike

"HK" wrote in message
. ..
Wayne.B wrote:
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)


I don't find it difficult. I simply remove the batteries before
shrinkwrapping and bring them home. That's one of the advantages of owning
boats where critical systems and subsystems are designed for easy access
and maintenance.

Don't forget to sweeten your batteries!
 

I have Cruis'n Rulz! hooked to a trickle charger, which is plugged into
an outlet in the garage that is hot when the garage lights are on. So,
when I'm in the basement garage fooling around, the boat gets a top off.
Works well.
JR

HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.



--
--------------------------------------------------------------
Home Page: http://www.seanet.com/~jasonrnorth

Don't forget to sweeten your batteries!
 

On Dec 26, 7:21*pm, HK wrote:
Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Eh, I put one in the wood splitter, and another in the 8-N Ford
tractor...

They'll stay charged all winter

Don't forget to sweeten your batteries!
 

On Dec 26, 9:51*pm, JR North wrote:
I have Cruis'n Rulz! hooked to a trickle charger, which is plugged into
an outlet in the garage that is hot when the garage lights are on. So,
when I'm in the basement garage fooling around, the boat gets a top off.
Works well.
JR


my brother does something similar. Living on a farm, he has several
odd batteries,t hat just "sit", so he got tired of buying batteries,
for stuff that doesn't get used much, SO......

He changed all his ends over to wing nut type stuff, and even though
there's no heat, he does have an old smoke house, where he has the
batteries lined up and connected with 10 ga. wire. His 10a. battery
charger is wired in with his well water pump. take a shower, the
batteries get a zap. cows get a drink, batteries get zapped. wash
dishes, cloths, ...

If he needs one for his 4 wheeler, he pulls it out of the line, hooks
it up and goes. same thing with his ancient 'Willy's jeep, Oliver 88
tractor, semi-truck, combine, etc, etc, He probably hasn't bought a
battery in 4 years.

Don't forget to sweeten your batteries!
 

"Wayne.B" wrote in message
...
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)


Unlike Harry I have faith in modern, 3 stage chargers with a "float mode"
maintainer that is intended to be left on permanently. The Navigator has a
dual output version used to charge and maintain the thruster batteries.
It's been on 24/7 for over 3 years now, the batteries are in excellent shape
and have never needed to have water added. The three other batteries on the
boat (3-8D's) are charged with an older ferroresonant, 3 output charger.
Those batteries have already been replaced due to boil off after spending
time in Florida, plus I just replaced one again because we load tested it
and it had a bad cell. I explored replacing the older style charger with a
modern, 3 stage "smart charger", but the price for a 3 output, 80-100 amp
unit was too high to justify. It's cheaper to replace the 8D's every 4 or 5
years.

I also have had excellent service from several small, Schumacher Electric
1.5-2 ampere battery float type battery maintainers. They are inexpensive
(about 20 bucks) and cost pennies a month to operate. I use them on both
motorcycles, the GTO, the Porsche and the JD tractor during the winter. I
leave them on 24/7 (as they are designed and intended to be used) and they
keep the batteries in good state of charge without overcharging. Before
using them I usually had to replace the motorcycle batteries every spring.
Keeping the batteries charged on modern vehicles like the newer Harley and
the Porsche is also important because there is a small but significant draw
on the battery while the vehicle is in storage due to the theft alarms and
the radio memory.

The diesel tractor is left outside and it fires up on the coldest of days
thanks to the fully charged battery. That reminds me. I need to pick up
another Schumacher for the little Boston Whaler's battery.

Eisboch

Don't forget to sweeten your batteries!
 

"HK" wrote in message
. ..

Wayne.B wrote:
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)


I don't find it difficult. I simply remove the batteries before
shrinkwrapping and bring them home. That's one of the advantages of owning
boats where critical systems and subsystems are designed for easy access
and maintenance.

Then you would *love* the design and layout of the Navigator's engine room
space.

Eisboch

Don't forget to sweeten your batteries!
 

"Gene Kearns" wrote in message
...
On Wed, 26 Dec 2007 20:21:41 -0500, HK penned the following well
considered thoughts to the readers of rec.boats:


Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

I'll probably do that tomorrow... too...



By the way Harry, just because your charger (I assume it's a Vector smart
charger) reads "FUL" after a minute of occasional charging during storage,
doesn't mean it is. It's simply responding to the voltage surface charge.
Ideally, the battery should be drawn down a bit before charging, allowing
the Vector to go through it's full bulk, absorption and float stages.

Eisboch

Don't forget to sweeten your batteries!
 

On Thu, 27 Dec 2007 03:13:21 -0500, "Eisboch" wrote:


"Wayne.B" wrote in message
.. .
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)


Unlike Harry I have faith in modern, 3 stage chargers with a "float mode"
maintainer that is intended to be left on permanently. The Navigator has a
dual output version used to charge and maintain the thruster batteries.
It's been on 24/7 for over 3 years now, the batteries are in excellent shape
and have never needed to have water added. The three other batteries on the
boat (3-8D's) are charged with an older ferroresonant, 3 output charger.
Those batteries have already been replaced due to boil off after spending
time in Florida, plus I just replaced one again because we load tested it
and it had a bad cell. I explored replacing the older style charger with a
modern, 3 stage "smart charger", but the price for a 3 output, 80-100 amp
unit was too high to justify. It's cheaper to replace the 8D's every 4 or 5
years.

I also have had excellent service from several small, Schumacher Electric
1.5-2 ampere battery float type battery maintainers. They are inexpensive
(about 20 bucks) and cost pennies a month to operate. I use them on both
motorcycles, the GTO, the Porsche and the JD tractor during the winter. I
leave them on 24/7 (as they are designed and intended to be used) and they
keep the batteries in good state of charge without overcharging. Before
using them I usually had to replace the motorcycle batteries every spring.
Keeping the batteries charged on modern vehicles like the newer Harley and
the Porsche is also important because there is a small but significant draw
on the battery while the vehicle is in storage due to the theft alarms and
the radio memory.

The diesel tractor is left outside and it fires up on the coldest of days
thanks to the fully charged battery. That reminds me. I need to pick up
another Schumacher for the little Boston Whaler's battery.

Eisboch


Thanks. I needed the reminder to put the bike battery on the charger.

Done.

Don't forget to sweeten your batteries!
 

On Thu, 27 Dec 2007 03:20:58 -0500, "Eisboch" wrote:


"HK" wrote in message
...

Wayne.B wrote:
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. :-)


I don't find it difficult. I simply remove the batteries before
shrinkwrapping and bring them home. That's one of the advantages of owning
boats where critical systems and subsystems are designed for easy access
and maintenance.

Then you would *love* the design and layout of the Navigator's engine room
space.

I agree. I got in and out of "Soul Source's" engine room - it's open
with plenty of room to move around and work on stuff.

I was impressed.

Don't forget to sweeten your batteries!
 

On Thu, 27 Dec 2007 03:13:21 -0500, "Eisboch" wrote:

I also have had excellent service from several small, Schumacher Electric
1.5-2 ampere battery float type battery maintainers.

That's what I use on my start battery.

The trolling motor batteries are charged off the built in float
charger.

Don't forget to sweeten your batteries!
 

On Dec 26, 11:05*pm, Tim wrote:
On Dec 26, 7:21*pm, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Eh, I put one in the wood splitter, and another in the 8-N Ford
tractor...

They'll stay charged all winter

My 8N is still set up with 6 volts!

Don't forget to sweeten your batteries!
 

On Dec 27, 3:20*am, "Eisboch" wrote:
"HK" wrote in message

. ..





Wayne.B wrote:
On Wed, 26 Dec 2007 21:08:22 -0500, HK wrote:

You do it your way, I'll do it mine. It costs only a couple of pennies
to do it my way.

Cost is not the issue, difficulty is. *Unless you take your batteries
off the boat (also overkill in my experience), then you have to go out
to the boatyard, run extension cords, get under the winter cover, etc.
When we lived north I eventually came to the conclusion that none of
that was really necessary. *This was somewhat influenced by ownership
of a boat that had 160 pound 8D batteries. *:-)

I don't find it difficult. I simply remove the batteries before
shrinkwrapping and bring them home. That's one of the advantages of owning
boats where critical systems and subsystems are designed for easy access
and maintenance.

Then you would *love* the design and layout of the Navigator's engine room
space.

Eisboch- Hide quoted text -

- Show quoted text -

Or a canoe!

Don't forget to sweeten your batteries!
 

wrote:
On Dec 26, 11:05?pm, Tim wrote:
On Dec 26, 7:21?pm, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Eh, I put one in the wood splitter, and another in the 8-N Ford
tractor...

They'll stay charged all winter

My 8N is still set up with 6 volts!

I changed my grandpa's over about 25 years ago. it starts a whole lot
easier....

Don't forget to sweeten your batteries!
 

On Dec 27, 1:17*pm, Tim wrote:
wrote:
On Dec 26, 11:05?pm, Tim wrote:
On Dec 26, 7:21?pm, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Eh, I put one in the wood splitter, and another in the 8-N Ford
tractor...

They'll stay charged all winter

My 8N is still set up with 6 volts!

I changed my grandpa's over about 25 years ago. it starts a whole lot
easier....

Yeah, mine's in pretty decent shape, and it doesn't get super cold
here, so it's one of those things that I've never gotten around to
doing!

Don't forget to sweeten your batteries!
 

"Short Wave Sportfishing" wrote in message
...
On Thu, 27 Dec 2007 03:13:21 -0500, "Eisboch" wrote:

I also have had excellent service from several small, Schumacher Electric
1.5-2 ampere battery float type battery maintainers.

That's what I use on my start battery.

The trolling motor batteries are charged off the built in float
charger.

Never charge the start battery, as seems to not need it. The trolling motor
batteries are charged with a Vector 1093 smart charger. Will pump out 35
amps and might be the thing for Eisbocks batteries.

Don't forget to sweeten your batteries!
 

"Tim" wrote in message
...


wrote:
On Dec 26, 11:05?pm, Tim wrote:
On Dec 26, 7:21?pm, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.

Eh, I put one in the wood splitter, and another in the 8-N Ford
tractor...

They'll stay charged all winter

My 8N is still set up with 6 volts!

I changed my grandpa's over about 25 years ago. it starts a whole lot
easier....

I had a 43' Ford built flat fender jeep a lot of years ago, and we went to
an 8 volt battery. Started a lot easier and did not screw up the lights,
etc. Unfortunately, someone used the nice towbar to take it away without
permission.

Don't forget to sweeten your batteries!
 

Calif Bill wrote:

I had a 43' Ford built flat fender jeep a lot of years ago, and we went to
an 8 volt battery. Started a lot easier and did not screw up the lights,
etc. Unfortunately, someone used the nice towbar to take it away without
permission.

Worse yet. When I was a kid in the early 60's my uncle cut up a Ford
"SEEP" for scrap!

Don't forget to sweeten your batteries!
 

"Calif Bill" wrote in message
...

"Short Wave Sportfishing" wrote in message
...
On Thu, 27 Dec 2007 03:13:21 -0500, "Eisboch" wrote:

I also have had excellent service from several small, Schumacher Electric
1.5-2 ampere battery float type battery maintainers.

That's what I use on my start battery.

The trolling motor batteries are charged off the built in float
charger.

Never charge the start battery, as seems to not need it. The trolling
motor batteries are charged with a Vector 1093 smart charger. Will pump
out 35 amps and might be the thing for Eisbocks batteries.


I'd need three of them. Frankly, I haven't had good luck with Vector
chargers. I've had three of them and they all died an early death. The
switching power supply craps out.

The equivalent Schumacher smart chargers haven't died yet although one has a
sticky fan that doesn't always like to start.

Eisboch

Don't forget to sweeten your batteries!
 

"Eisboch" wrote in message
...

"Calif Bill" wrote in message
...

"Short Wave Sportfishing" wrote in message
...
On Thu, 27 Dec 2007 03:13:21 -0500, "Eisboch" wrote:

I also have had excellent service from several small, Schumacher
Electric
1.5-2 ampere battery float type battery maintainers.

That's what I use on my start battery.

The trolling motor batteries are charged off the built in float
charger.

Never charge the start battery, as seems to not need it. The trolling
motor batteries are charged with a Vector 1093 smart charger. Will pump
out 35 amps and might be the thing for Eisbocks batteries.


I'd need three of them. Frankly, I haven't had good luck with Vector
chargers. I've had three of them and they all died an early death. The
switching power supply craps out.

The equivalent Schumacher smart chargers haven't died yet although one has
a sticky fan that doesn't always like to start.

Eisboch


My vector is at least 3 years old.

Don't forget to sweeten your batteries!
 

Don White wrote:
"HK" wrote in message
. ..
Wayne.B wrote:
On Wed, 26 Dec 2007 20:21:41 -0500, HK wrote:

Just charged up all of my boat batteries. Each battery took under a
minute to get to "FUL" on the charger. This is something to do once a
month, unless you have one of those reliable, low output, always
connected chargers.
Once a month is overkill in my experience. If the batteries are in
good condition, fully charged at winterization, and totally
disconnected from all loads, they will start right up in the spring.

You do it your way, I'll do it mine. It costs only a couple of pennies to
do it my way.


Thanks for the reminder. Mine has been sitting out in the shed for a couple
months.
I may bring it into the cool basement rather than the freezing shed.



Have your boy drag it in. Sit back with a cold beer and relax!