Ping: Gene
 

Don White wrote:
"RG" wrote in message
...
"Don White" wrote in message
...
"Short Wave Sportfishing" wrote in message
...
You and Gene make this much more complicated that it has to be.

Just take a ten penny nail and punch a freakin' hole.

~~ sheesh ~~

...and what size tool do you recommend for the task...a 3 lb cub hammer?
I'm thinking your head on a stick would be just about perfect for the job.
Stick optional.

Maybe..it's hard enough. On the other hand, your marshmallow noggin is
probably as firm as your lower extremities.



So typical. Is this considered to be humor in Canada?

Ping: Gene
 

On May 8, 6:27 pm, Short Wave Sportfishing wrote:
On 8 May 2007 16:07:58 -0700, wrote:





On May 8, 6:47 pm, Gene Kearns
wrote:
On Tue, 8 May 2007 18:05:43 -0400, JimH penned the following well
considered thoughts to the readers of rec.boats:

I need to drill some new bolt holes in 1" and 3/4" diameter SS tubing to add
a step to my swim platform ladder.

Will I need a special drill bit for this or will my ordinary metal cutting
drill bit work?

Thanks!

My personal choice would be to drill a pilot hole through both sides
of the tubing (from one side) about 1/16 of an inch or so in diameter.

I would, then, use a unibit to size the holes.http://www.crawfordtool.com/unibit.html

The pilot hole will insure that the holes enlarged by the unibit line
up. The unibit has a straight flute and will not grab in the tubing.

Depending on the size of the screws, you probably can get away with
just drilling through with a conventional bit, but bear in mind, when
the tip breaks through it is going to try to screw it's way through
the tubing and grab.

Unibits can be bought pretty cheap at places like Northern Tool or
Harbor Freight.

Stainless steel = slow speed and positive feed, don't let the drill
rub without cutting.

--

Grady-White Gulfstream, out of Oak Island, NC.

Homepagehttp://pamandgene.idleplay.net/

Rec.boats at Lee Yeaton's Bayguidehttp://www.thebayguide.com/rec.boats

I know you did not ping me, but I would also go with a pilot hole, and
slow, positive feed, etc. First however I would probably make a quick
jig (from a chunk of maple I keep around for just such an
occasion ;)and use a drill press. I would put a pilot in one side,
then line the piece and jig up in the clamps. This allows for a very
quick way to get the 2 pilot holes lined up correctly. Then I would
work my way up to the correct size with good bits.

You and Gene make this much more complicated that it has to be.

Just take a ten penny nail and punch a freakin' hole.

~~ sheesh ~~- Hide quoted text -

- Show quoted text -

That may be alright for you and I, Tom. But maybe he doesn't want a
flat dent int he pipe, and squished index and thumb joints when the
hammer clobbers them between the hammer head and the pipes.


Sofistication, can be more meticulous, but less fun and rewarding.

Ping: Gene
 

On May 8, 6:47 pm, "Don White" wrote:


...and what size tool do you recommend for the task...a 3 lb cub hammer?

a 3 lb "cub hammer?"


That light???

Ping: Gene
 

"Dan" wrote in message
...
Don White wrote:
"RG" wrote in message
...
"Don White" wrote in message
...
"Short Wave Sportfishing" wrote in message
...
You and Gene make this much more complicated that it has to be.

Just take a ten penny nail and punch a freakin' hole.

~~ sheesh ~~

...and what size tool do you recommend for the task...a 3 lb cub
hammer?
I'm thinking your head on a stick would be just about perfect for the
job. Stick optional.

Maybe..it's hard enough. On the other hand, your marshmallow noggin is
probably as firm as your lower extremities.

So typical. Is this considered to be humor in Canada?

Who's laughing?

Ping: Gene
 

Don White wrote:
"Dan" wrote in message
...
Don White wrote:
"RG" wrote in message
...
"Don White" wrote in message
...
"Short Wave Sportfishing" wrote in message
...
You and Gene make this much more complicated that it has to be.

Just take a ten penny nail and punch a freakin' hole.

~~ sheesh ~~
...and what size tool do you recommend for the task...a 3 lb cub
hammer?
I'm thinking your head on a stick would be just about perfect for the
job. Stick optional.

Maybe..it's hard enough. On the other hand, your marshmallow noggin is
probably as firm as your lower extremities.
So typical. Is this considered to be humor in Canada?

Who's laughing?


Exactly.

Ping: Gene
 

"Gene Kearns" wrote in message
...
On Tue, 08 May 2007 18:47:02 -0400, Gene Kearns penned the following
well considered thoughts to the readers of rec.boats:

On Tue, 8 May 2007 18:05:43 -0400, JimH penned the following well
considered thoughts to the readers of rec.boats:

I need to drill some new bolt holes in 1" and 3/4" diameter SS tubing to
add
a step to my swim platform ladder.

Will I need a special drill bit for this or will my ordinary metal
cutting
drill bit work?

Thanks!


My personal choice would be to drill a pilot hole through both sides
of the tubing (from one side) about 1/16 of an inch or so in diameter.

I would, then, use a unibit to size the holes.
http://www.crawfordtool.com/unibit.html

The pilot hole will insure that the holes enlarged by the unibit line
up. The unibit has a straight flute and will not grab in the tubing.

Depending on the size of the screws, you probably can get away with
just drilling through with a conventional bit, but bear in mind, when
the tip breaks through it is going to try to screw it's way through
the tubing and grab.

Unibits can be bought pretty cheap at places like Northern Tool or
Harbor Freight.

Stainless steel = slow speed and positive feed, don't let the drill
rub without cutting.

Jim,

Email me a good email address......

--

Grady-White Gulfstream, out of Oak Island, NC.

Homepage
http://pamandgene.idleplay.net/

Rec.boats at Lee Yeaton's Bayguide
http://www.thebayguide.com/rec.boats

Done