How to temporarily stop a leak?
 

Hi,

We've got a steel hull houseboat. Recently we pulled it
to work on the outdrive, and when it went back in it
began leaking. Swimming under the boat I found that
about 2" of a plate weld has rusted and cracked. The
inlet for the toilet's water is right beside the leak, and it
looks to me like the hole in that location weakened the
weld, so the stress from being on the trailer was enough
to crack it.

Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?

How to temporarily stop a leak?
 

You can use a two part epoxy putty for an "emergency" repair, but I wouldn't
trust it for any longer than it took to get the boat hauled and properly
restored. Personally would never slap on some goop and then take off on a
holiday cruise as if there were no problem.

How to temporarily stop a leak?
 

Davis makes a product called "Slick Seam Compound" that can be applied
underwater. I've never used it but it may be worth looking into. Found it in
a West Marine catalog.

--
Bill
Chesapeake, Va


wrote in message
...
Hi,

We've got a steel hull houseboat. Recently we pulled it
to work on the outdrive, and when it went back in it
began leaking. Swimming under the boat I found that
about 2" of a plate weld has rusted and cracked. The
inlet for the toilet's water is right beside the leak, and it
looks to me like the hole in that location weakened the
weld, so the stress from being on the trailer was enough
to crack it.

Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?

How to temporarily stop a leak?
 

In article iVaMc.7901$fB4.1955@lakeread01, "IBNFSHN"
wrote:

According to a recent TV commercial I saw, use a tampon.

--
Member AAAAAAAA
American Association Against Acronym Abuse And Also Ambiguity.

How to temporarily stop a leak?
 

In article ,
says...
Hi,

We've got a steel hull houseboat. Recently we pulled it
to work on the outdrive, and when it went back in it
began leaking. Swimming under the boat I found that
about 2" of a plate weld has rusted and cracked. The
inlet for the toilet's water is right beside the leak, and it
looks to me like the hole in that location weakened the
weld, so the stress from being on the trailer was enough
to crack it.

Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?

You may want to look at RayCrete

http://www.leevalley.com/garden/page...D5&ccurrency=2
&page=44730&category=2,42194,40727


--
MikeG
Heirloom Woods
www.heirloom-woods.net

How to temporarily stop a leak?
 

In article ,
says...
Hi,

We've got a steel hull houseboat. Recently we pulled it
to work on the outdrive, and when it went back in it
began leaking. Swimming under the boat I found that
about 2" of a plate weld has rusted and cracked. The
inlet for the toilet's water is right beside the leak, and it
looks to me like the hole in that location weakened the
weld, so the stress from being on the trailer was enough
to crack it.

Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?



You may want to look at RayCrete

http://www.leevalley.com/garden/page...D5&ccurrency=2
&page=44730&category=2,42194,40727


--
MikeG
Heirloom Woods
www.heirloom-woods.net

How to temporarily stop a leak?
 

On Friday 23 July 2004 4:36 pm in rec.boats wrote:


Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?

There are several expensive varieties of snake oil available from
chandlers, but the traditional patch is best.
Slather a good layer of bitumin onto a piece of canvas and slap it
over the hole. Smooth the patch over (a roller is a good idea) and
water pressure will keep it in place.
When the boat is pulled just pull off the patch and clean up with
kerosene or white spirit..


--
My real address is crn (at) netunix (dot) com
WARNING all messages containing attachments or html will be silently
deleted. Send only plain text.

How to temporarily stop a leak?
 

Splash Zone
wrote in message
...
Hi,

We've got a steel hull houseboat. Recently we pulled it
to work on the outdrive, and when it went back in it
began leaking. Swimming under the boat I found that
about 2" of a plate weld has rusted and cracked. The
inlet for the toilet's water is right beside the leak, and it
looks to me like the hole in that location weakened the
weld, so the stress from being on the trailer was enough
to crack it.

Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?

How to temporarily stop a leak?
 

On Fri, 23 Jul 2004 11:24:01 -0500, Jeepers
wrote:

In article iVaMc.7901$fB4.1955@lakeread01, "IBNFSHN"
wrote:

According to a recent TV commercial I saw, use a tampon.

Damn, beat me to it. :)

Later,

Tom

How to temporarily stop a leak?
 

That won't stop a leak. It's kinda a waxy paste to smear in the planking
seams of a wood boat below the waterline. Doesn't work particularly well for
that either.

"IBNFSHN" wrote in message
news:iVaMc.7901$fB4.1955@lakeread01...
Davis makes a product called "Slick Seam Compound" that can be applied
underwater. I've never used it but it may be worth looking into. Found it
in
a West Marine catalog.

--
Bill
Chesapeake, Va


wrote in message
...
Hi,

We've got a steel hull houseboat. Recently we pulled it
to work on the outdrive, and when it went back in it
began leaking. Swimming under the boat I found that
about 2" of a plate weld has rusted and cracked. The
inlet for the toilet's water is right beside the leak, and it
looks to me like the hole in that location weakened the
weld, so the stress from being on the trailer was enough
to crack it.

Most of the rest of the bottom looks in pretty fair shape,
though it will need to be pulled and at least painted
before too long. Can anyone suggest a good way to
temporarily plug the leak for a while? Is there anything
that can be applied under water, but won't be too hard
to remove later when the boat is pulled and fixed correctly?