Strange question: trailering with a dog in the vehicle
 

My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...

Strange question: trailering with a dog in the vehicle
 

I don't know if the clunking or "slop" is normal, or caused perhaps by
less-than-good-quality parts. I had the same problem (minus the dog) hauling
at 6x12 utility trailer using a 6" drop hitch in my receiver. I also don't
know if it's recommended or not, but here's what I did to eliminate the
slack:

Run two beads of weld on each of two adjoining sides of the hitch box.
Patiently (with file or grinder) remove enough of the weld from both front
and rear of both sides to achieve a good fit. I ran beads which did not
extend into the radiused portion of the hitch box and were approximately
1/4" to 3/8" in width. One set was about 1" from the front end, the other
about 1/2 to 1" from the end of where it rests in the receiver.

Initially I was concerned that a tighter fit would cause binding problems if
I chose to remove the hitch, but I think any substantial trailer load
eventually wears the weld beads and/or inside of the receiver enough that
this was not a problem.

For the record, my receiver and frame is also a "Reese" unit. The drop hitch
was purchased locally at a Tractor Supply store. Hope this helps (or at
least solicits some interesting responses...).

"Spencer" wrote in message
m...
My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...

Strange question: trailering with a dog in the vehicle
 

There is a company that makes a rubber cushioned ball mount. This prevents
the clunking and jerking that your are experiencing. Do a search on hitch
accessories and you should be able to find the product.

Buck
"Spencer" wrote in message
m...
My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...

Strange question: trailering with a dog in the vehicle
 

Wouldn't it be easier to just train the dog to be quiet? Muzzle? Or maybe
desensitize him by banging on the hitch while the dog is in the car?

Strange question: trailering with a dog in the vehicle
 

"Floyd in Tampa" wrote in message
m...
Wouldn't it be easier to just train the dog to be quiet? Muzzle? Or
maybe
desensitize him by banging on the hitch while the dog is in the car?


I can tell that you have never had to deal with a nervous dog.....

Rod

Strange question: trailering with a dog in the vehicle
 

In article ,
says...
My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...


A trip to the vet to get some good dog prozac would seem simpler to me
--
MikeG
Heirloom Woods
www.heirloom-woods.net

Strange question: trailering with a dog in the vehicle
 

Thanks Buck - I'll see what I can find...

"buck183" wrote in message ...
There is a company that makes a rubber cushioned ball mount. This prevents
the clunking and jerking that your are experiencing. Do a search on hitch
accessories and you should be able to find the product.

Buck
"Spencer" wrote in message
m...
My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...

Strange question: trailering with a dog in the vehicle
 

Maybe down the road, but for the odd-few times that I want to pull a
trailer with my dog in the vehicle before actually getting a boat, I
want to see if there are any reasonable mechanical means to help
alleviate the problem. Good suggestions nonetheless, thanks.

"Floyd in Tampa" wrote in message om...
Wouldn't it be easier to just train the dog to be quiet? Muzzle? Or maybe
desensitize him by banging on the hitch while the dog is in the car?

Strange question: trailering with a dog in the vehicle
 

Great Idea Buck!
The best place (at least around here) to find one of those cushioned mounts
is Tractor Supply.
I know there are similar farm related co-op type stores all over most of the
USA.
Usually beat the Hell out of UHaul and specialty towing / RV stores on
price, too.

"buck183" wrote in message
...
There is a company that makes a rubber cushioned ball mount. This
prevents
the clunking and jerking that your are experiencing. Do a search on hitch
accessories and you should be able to find the product.

Buck
"Spencer" wrote in message
m...
My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...

Strange question: trailering with a dog in the vehicle
 

Any other mechanical (non-dog related) fix suggestions?

(Spencer) wrote in message om...
My wife and I would eventually like to get a boat which would
inevitably involve trailering. The problem with this scheme happens
to be our dog. A few months ago, we pulled a trailer (with decent
loading at the hitch) with our SUV and Reese hitch (square socket
receiver). When there were bumps or speed changes, the clunks just
drove our dog wild who was in the back of the SUV. We'd like to
prevent that kind of trauma again if we were to pull a trailer. Does
anyone have any tips as to how to prevent the clunking? I'm not sure
if the clunking was primarily coming from the receiver hitch or the
ball/trailer connection, but since we had good loading on the ball,
I'm guessing it was the receiver. Anyone else had the clunking
problem? Any solutions? (I was thinking about using some sort of
shims in the receiver, but I'm not sure that would work if we were to
drive several hundred miles...) Thanks!

ps. NOT bringing the dog is certainly one solution, but unacceptable
at this time...