How does choke work on 1998 Merc 90ELPTO
 

Can anyone kindly explain the choke operation on a 1998 Merc 90ELPTO? I
just bought a used boat with this motor and I would like to know the
"correct" way to start the motor with the choke, and how the choke
works. What I was told by the salesman was the ignition key can be
pressed in to "engage the choke". Does pressing in the key BEFORE
cranking the motor "preengage" the choke? Does pressing the key in
squirt gas in the carbs each time it is pushed in? Or does pushing the
key in just enrich the mixture while it is pushed in? Should you press
the key in once and then crank? Or do you have to hold the key in while
cranking, and then maybe a little after it starts? What about the "fast
idle" lever? What is the best way to work that into the procedure?

I think I would have better luck starting the motor if I actually knew
what was going on with the choke!

Thanks in advance...

How does choke work on 1998 Merc 90ELPTO
 

"Ted" wrote in message ...
Can anyone kindly explain the choke operation on a 1998 Merc 90ELPTO? I
just bought a used boat with this motor and I would like to know the
"correct" way to start the motor with the choke, and how the choke
works. What I was told by the salesman was the ignition key can be
pressed in to "engage the choke". Does pressing in the key BEFORE
cranking the motor "preengage" the choke? Does pressing the key in
squirt gas in the carbs each time it is pushed in? Or does pushing the
key in just enrich the mixture while it is pushed in? Should you press
the key in once and then crank? Or do you have to hold the key in while
cranking, and then maybe a little after it starts? What about the "fast
idle" lever? What is the best way to work that into the procedure?

I think I would have better luck starting the motor if I actually knew
what was going on with the choke!

Thanks in advance...

Ok, let's square you away on how a choke works, and to do that we need to do
Carb 101. A carb is a venturi, when you flow air through a venturi it
creates a low pressure area just downstream from the expanse in the neck.
This low pressure is what pulls the fuel from the bowl through the metering
jet and into the engine. The "choke" is a plate at the opening of the
venturi which when engaged, restricts the airflow, thereby further reducing
the absolute pressure in the venturi causing the fuel to come through the
jet at a higher rate. So you see, the engine has to be turning for the choke
to have any effect whatsoever. On these motors, the choke is activated by an
electric solenoid which is what you hear go "click" on the motor when you
push the key in. It releases when you release the key, therefore you have to
hold the key in while you are cranking in order for the choke to have any
effect.
Chokes do not "squirt" gas into engines, however, some carburetors are
equipped with accelerator pumps which "squirt" a metered amount of fuel into
the engine as you advance the throttle.

Hope this helped unconfuse you.

How does choke work on 1998 Merc 90ELPTO
 

My Mercury outboard was simmilar.

Throttle / fast idle lever: If the engine is cold or otherwise stalling
just after you start it then a little faster idle might be helpful. So
moving
this lever a little (but not much) will help. Besides, if it's idleing too
fast
once it's started you can always move the lever back down/off.

As HL described, you have to hold the key in for the choke to be on.
Normally when the engine is cold, hold the key in while starting.
Once started you can let it out.

You might also have to adjust the idle on the engine if it's set too low.

How does choke work on 1998 Merc 90ELPTO
 

HLAviation wrote:

"Ted" wrote in message ...
Can anyone kindly explain the choke operation on a 1998 Merc 90ELPTO? I
just bought a used boat with this motor and I would like to know the
"correct" way to start the motor with the choke, and how the choke
works. What I was told by the salesman was the ignition key can be
pressed in to "engage the choke". Does pressing in the key BEFORE
cranking the motor "preengage" the choke? Does pressing the key in
squirt gas in the carbs each time it is pushed in? Or does pushing the
key in just enrich the mixture while it is pushed in? Should you press
the key in once and then crank? Or do you have to hold the key in while
cranking, and then maybe a little after it starts? What about the "fast
idle" lever? What is the best way to work that into the procedure?

I think I would have better luck starting the motor if I actually knew
what was going on with the choke!

Thanks in advance...

Ok, let's square you away on how a choke works, and to do that we need to do
Carb 101. A carb is a venturi, when you flow air through a venturi it
creates a low pressure area just downstream from the expanse in the neck.
This low pressure is what pulls the fuel from the bowl through the metering
jet and into the engine. The "choke" is a plate at the opening of the
venturi which when engaged, restricts the airflow, thereby further reducing
the absolute pressure in the venturi causing the fuel to come through the
jet at a higher rate. So you see, the engine has to be turning for the choke
to have any effect whatsoever. On these motors, the choke is activated by an
electric solenoid which is what you hear go "click" on the motor when you
push the key in. It releases when you release the key, therefore you have to
hold the key in while you are cranking in order for the choke to have any
effect.
Chokes do not "squirt" gas into engines, however, some carburetors are
equipped with accelerator pumps which "squirt" a metered amount of fuel into
the engine as you advance the throttle.

Hope this helped unconfuse you.

Hi HL:

Actually, I understand how chokes work, and I was using the term "choke"
loosely (incorrectly) here. On my '65 Triumph Bonneville, I had no choke
plate, but a button that depressed the float, so the float bowl would be
tricked into thinking it was empty and would allow gas to flood the
carb. This worked very well actually. Those carbs had no choke plates
but I could start that bike on the coldest days! What do you call that
type of "choke"? A squirter? When the salesman told me to press the key
in, I envisioned a similiar arrangement, that would simply be squirting
gas in.

Best Regards

How does choke work on 1998 Merc 90ELPTO
 

Gary Warner wrote:

My Mercury outboard was simmilar.

Throttle / fast idle lever: If the engine is cold or otherwise stalling
just after you start it then a little faster idle might be helpful. So
moving
this lever a little (but not much) will help. Besides, if it's idleing too
fast
once it's started you can always move the lever back down/off.

As HL described, you have to hold the key in for the choke to be on.
Normally when the engine is cold, hold the key in while starting.
Once started you can let it out.

You might also have to adjust the idle on the engine if it's set too low.

Hi:
So if the engine is cold, after you press the key in, and turn it
clockwise, once the engine fires, do you turn the key counterclockwise
and continue pressing the key forward to keep it going? On my old 25
Johnson, I would have to leave the choke on for a while to keep it
running.

Thanks

How does choke work on 1998 Merc 90ELPTO
 

That is a good description of how a choke works, but do you have a choke? Or
an enrichner? If it is an enrichner, you turn the key on and then hold it in
for a few seconds, release and then start. How long varies with each engine.

--
Bill
Chesapeake, Va


"HLAviation" wrote in message
ink.net...

"Ted" wrote in message
...
Can anyone kindly explain the choke operation on a 1998 Merc 90ELPTO? I
just bought a used boat with this motor and I would like to know the
"correct" way to start the motor with the choke, and how the choke
works. What I was told by the salesman was the ignition key can be
pressed in to "engage the choke". Does pressing in the key BEFORE
cranking the motor "preengage" the choke? Does pressing the key in
squirt gas in the carbs each time it is pushed in? Or does pushing the
key in just enrich the mixture while it is pushed in? Should you press
the key in once and then crank? Or do you have to hold the key in while
cranking, and then maybe a little after it starts? What about the "fast
idle" lever? What is the best way to work that into the procedure?

I think I would have better luck starting the motor if I actually knew
what was going on with the choke!

Thanks in advance...

Ok, let's square you away on how a choke works, and to do that we need to
do
Carb 101. A carb is a venturi, when you flow air through a venturi it
creates a low pressure area just downstream from the expanse in the neck.
This low pressure is what pulls the fuel from the bowl through the
metering
jet and into the engine. The "choke" is a plate at the opening of the
venturi which when engaged, restricts the airflow, thereby further
reducing
the absolute pressure in the venturi causing the fuel to come through the
jet at a higher rate. So you see, the engine has to be turning for the
choke
to have any effect whatsoever. On these motors, the choke is activated by
an
electric solenoid which is what you hear go "click" on the motor when you
push the key in. It releases when you release the key, therefore you have
to
hold the key in while you are cranking in order for the choke to have any
effect.
Chokes do not "squirt" gas into engines, however, some carburetors are
equipped with accelerator pumps which "squirt" a metered amount of fuel
into
the engine as you advance the throttle.

Hope this helped unconfuse you.