![]() |
Cape Fear Performance Report
First, know that I am the owner of JEM Watercraft. I designed and built
the Cape Fear 16 myself. I’ll try to be as objective as possible although I’m very pleased with how it did. The Cape Fear is designed as a recreational kayak so it’s meant for general purpose paddling, family outings, fishing in protected/calm waters, etc. Not meant to be as fast as a touring kayak or maneuverable as a white water yak. I paddled on March 20, 2004 in Greensboro, NC on lake Brandt. Somewhat windy conditions, 16-20 mph steady with an occasional gust. Brandt is an 816-acre municipal reservoir so it’s not huge but it’s big enough to let the wind kick up the water into a minor chop. I had 5-6 inches waves spaced in very short intervals and coming from different directions. You could look out and see the waves moving in different paths. Hardly ocean swells but not smooth waters. In addition, I had power boats zipping all around me. The launch from the dock area was good. But once I got around the tip of the inlet, instant wind. I wasn’t ready for it and the boat began to turn from the wind because I was at 45 degrees to the wind and waves. I corrected to go into the wind head on. Had a constant small choppy soup to deal with but the yak bit into the waves well and rolled over the bigger ones easily. I had a ski boat launching next to me so I stopped paddling to let him go by. Apparently he thought it would be fun to come within 20 yards of me and give the engine all it had. His wake came at me directly sideways but I was ready. The yak rolled nicely with no sudden tippy feeling. To be honest, I thought it would be worse. The power boat was moving pretty good by the time he passed me. She tracked very well through the wind and soup I was in. But it got old quick. It was the kind of conditions where you put your paddle in the water and it feels likes it’s getting pulled through the water at the beginning of your stroke. She handled very well and not once did it feel unstable. I built her light out of marine plywood and fiberglass. Very responsive compared to the Tarpon 160 I paddled recently. I’ll get an official weight soon. Can you believe I don’t have a scale in the house? I finally got over to one of the coves about ½ mile away where the wind was blocked and I could play around. Maneuverability was good to very good for a 16-foot yak. I leaned over to heel her up to the upper chine, 22 degrees, and she felt very stable. No tippy feeling or sudden “loose” spots. Since I’m designing this one to be also made as a Sit On Top, I brought along something to raise my seat position to simulate a SOT. I taped 2 Greensboro, NC phone books inside a plastic bag together for a total height of 6 inches, which will be 2 more than the seat height I intend for the SOT. I grabbed them from the back and the yak felt very stable as I was turning around and messing with the gear. Sat on top of the books and started to paddle. I noticed very little difference in stability. I was quite pleased. I liked the higher paddling position better because I when sitting on the floor as a Side-Inside, it felt like I was raising my paddle about 2 inches higher than I would with my normal strokes. I cruised around, made some turns, leaned back and forth while on the phone books. No problem at all. With me being 6’2 and 220 pounds and I had about 20 pounds worth of stuff with me, she drafted only about 3-3.5 inches of water. I judged this be putting my middle finger tip in the water and then held it against the side of the boat. The upper chine, which is 6.5” above the bottom at mid-ship, came up to the top of my finger, which is 3” (I have long hands). To summarize: Pluses: Very stable even with the higher seating position. Plenty of reserve buoyancy. Tracked well. Turns well for a 16’ yak. Paddled efficiently but it was hard to get a really good feel because of the wind. Minuses: As a sit-inside, the sides are almost too high but that’s if you’re sitting on the floor. Get a nice seat cushion with 2” of padding and you’re golden. Wind grabbed it pretty good but I think almost any yak would have been tossed around. I’m pleased how it turned out. Should make for a very nice recreational yak and SOT once that design is done. Picture of the prototype at http://www.jem.e-boat.net/CapeFearProtoImages.php -- Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ |
Cape Fear Performance Report
Matt Langenfeld wrote in message ink.net...
First, know that I am the owner of JEM Watercraft. I designed and built the Cape Fear 16 myself. I’ll try to be as objective as possible although I’m very pleased with how it did. The Cape Fear is designed as a recreational kayak so it’s meant for general purpose paddling, family outings, fishing in protected/calm waters, etc. Not meant to be as fast as a touring kayak or maneuverable as a white water yak. I paddled on March 20, 2004 in Greensboro, NC on lake Brandt. Somewhat windy conditions, 16-20 mph steady with an occasional gust. Brandt is an 816-acre municipal reservoir so it’s not huge but it’s big enough to let the wind kick up the water into a minor chop. I had 5-6 inches waves spaced in very short intervals and coming from different directions. You could look out and see the waves moving in different paths. Hardly ocean swells but not smooth waters. In addition, I had power boats zipping all around me. The launch from the dock area was good. But once I got around the tip of the inlet, instant wind. I wasn’t ready for it and the boat began to turn from the wind because I was at 45 degrees to the wind and waves. I corrected to go into the wind head on. Had a constant small choppy soup to deal with but the yak bit into the waves well and rolled over the bigger ones easily. I had a ski boat launching next to me so I stopped paddling to let him go by. Apparently he thought it would be fun to come within 20 yards of me and give the engine all it had. His wake came at me directly sideways but I was ready. The yak rolled nicely with no sudden tippy feeling. To be honest, I thought it would be worse. The power boat was moving pretty good by the time he passed me. She tracked very well through the wind and soup I was in. But it got old quick. It was the kind of conditions where you put your paddle in the water and it feels likes it’s getting pulled through the water at the beginning of your stroke. She handled very well and not once did it feel unstable. I built her light out of marine plywood and fiberglass. Very responsive compared to the Tarpon 160 I paddled recently. I’ll get an official weight soon. Can you believe I don’t have a scale in the house? I finally got over to one of the coves about ½ mile away where the wind was blocked and I could play around. Maneuverability was good to very good for a 16-foot yak. I leaned over to heel her up to the upper chine, 22 degrees, and she felt very stable. No tippy feeling or sudden “loose” spots. Since I’m designing this one to be also made as a Sit On Top, I brought along something to raise my seat position to simulate a SOT. I taped 2 Greensboro, NC phone books inside a plastic bag together for a total height of 6 inches, which will be 2 more than the seat height I intend for the SOT. I grabbed them from the back and the yak felt very stable as I was turning around and messing with the gear. Sat on top of the books and started to paddle. I noticed very little difference in stability. I was quite pleased. I liked the higher paddling position better because I when sitting on the floor as a Side-Inside, it felt like I was raising my paddle about 2 inches higher than I would with my normal strokes. I cruised around, made some turns, leaned back and forth while on the phone books. No problem at all. With me being 6’2 and 220 pounds and I had about 20 pounds worth of stuff with me, she drafted only about 3-3.5 inches of water. I judged this be putting my middle finger tip in the water and then held it against the side of the boat. The upper chine, which is 6.5” above the bottom at mid-ship, came up to the top of my finger, which is 3” (I have long hands). To summarize: Pluses: Very stable even with the higher seating position. Plenty of reserve buoyancy. Tracked well. Turns well for a 16’ yak. Paddled efficiently but it was hard to get a really good feel because of the wind. Minuses: As a sit-inside, the sides are almost too high but that’s if you’re sitting on the floor. Get a nice seat cushion with 2” of padding and you’re golden. Wind grabbed it pretty good but I think almost any yak would have been tossed around. I’m pleased how it turned out. Should make for a very nice recreational yak and SOT once that design is done. Picture of the prototype at http://www.jem.e-boat.net/CapeFearProtoImages.php Nice report. Do you build and test all of your plans before selling them? I ask cause I do not see finished hulls for many of the plans you have for sale. In the interest of full disclosure I must note that I too have a dozen or so sets of plans on the drawing board but only sell two of them as those are the only ones which have been built several times and extensively tested. Thanks for your response, Scotty from SmallBoats.com |
Cape Fear Performance Report
New concepts (plus to yaks/canoes I want for personal use) are prototpyed.
All my plans have a prototype that is an actual/similar design. Or are in the process of being built. Example: The Swamp Girl was a custom design request and then the builder built one and sent in pictures. I expect pictures of the Buccaneer and Hiawatha in the next week or 2. I have 3 other designs that are not currently shown being built that I'll release once I have pictures of them. So far I've had no incidences of a "bad design" (knock on marine plywood). So when I release plans without actual pictures, I'm pretty confident there will be no issues. Real pictures of boats actually built give credibility to your designs. Until you get a repuatation like Jacques Mertens, a new designer alomst has to prove themselves. BTW, I really like your War Canoe. Very cool lines! -- Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ Backyard Renegade wrote: Nice report. Do you build and test all of your plans before selling them? I ask cause I do not see finished hulls for many of the plans you have for sale. In the interest of full disclosure I must note that I too have a dozen or so sets of plans on the drawing board but only sell two of them as those are the only ones which have been built several times and extensively tested. Thanks for your response, Scotty from SmallBoats.com |
Cape Fear Performance Report
Matt Langenfeld wrote in message ink.net...
New concepts (plus to yaks/canoes I want for personal use) are prototpyed. All my plans have a prototype that is an actual/similar design. Or are in the process of being built. Example: The Swamp Girl was a custom design request and then the builder built one and sent in pictures. I expect pictures of the Buccaneer and Hiawatha in the next week or 2. I have 3 other designs that are not currently shown being built that I'll release once I have pictures of them. So far I've had no incidences of a "bad design" (knock on marine plywood). So when I release plans without actual pictures, I'm pretty confident there will be no issues. Real pictures of boats actually built give credibility to your designs. Until you get a repuatation like Jacques Mertens, a new designer alomst has to prove themselves. BTW, I really like your War Canoe. Very cool lines! Thanks. The WarCanoe is a perfect example.. That boat could make me a fortune in plans, I get requests constantly. I built 5 hulls before I got one that worked and have had no less than a dozen different paddlers of different skill levels use the boat, have taken it out a couple of dozen times myself, two seasons, pond, lake, river, sound... Hopefully, this season I will have enough info to feel confident enough to reccomend and sell the plans ;). I have to confess, my interest is selfish. I constantly worry about these computer generated plans being sold without being tested. If we as amateur designers are not careful we will end up with laws like the Brits which would put you and me completely out of business (as it were ;). Amateurs can not sell a boat for something like five years. If you wish to sell plans or boats professionally, you need to submit those plans the man for approval (read, many frekin' euros!), and to sell boats you must provide two completed hulls to the man (read, one for testing, one for his kids!) and have them "approved". If enough folks buy untested plans from some (not suggesting you) who really are not familiar with the style and use of the particular hull they drew and how it may act if someone for instance gets caught in the wrong conditins, folks could start getting hurt. Enough folks (or the right one person) get(s) hurt, we are liable to see rediculous regulations like many of our mates in Europe. This really scares the hell out of me as I don't build enough boats to make a living, but to many to keep them hanging around the yard... Scotty, rant-off, flame proof suit on ;) -- Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ Backyard Renegade wrote: Nice report. Do you build and test all of your plans before selling them? I ask cause I do not see finished hulls for many of the plans you have for sale. In the interest of full disclosure I must note that I too have a dozen or so sets of plans on the drawing board but only sell two of them as those are the only ones which have been built several times and extensively tested. Thanks for your response, Scotty from SmallBoats.com |
Cape Fear Performance Report
Excellent points. I don't want to put out anything that is risky. You
get a feel what works and what doesn't so you can "copy-paste" some features. But there are many rules I self-impose on my designs to make sure things are safe, functional, reliable, and have a safety margins for those possible "oop's" we all make! Even when I get custom design requests where the builder wants specific features, I still don't compromise safety. It's only happened one time where someone demanded something I wasn't willing to do. In that case I thanked him for his consideration and we parted ways. It's just not worth your reputation let alone someone's life. Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ |
Cape Fear Performance Report
You might want to be careful about marketing that as a "Cape Fear" design.
Cape Fear Yachts might get a bit upset about you atemptingt o steal their trademark! "Matt Langenfeld" wrote in message nk.net... Excellent points. I don't want to put out anything that is risky. You get a feel what works and what doesn't so you can "copy-paste" some features. But there are many rules I self-impose on my designs to make sure things are safe, functional, reliable, and have a safety margins for those possible "oop's" we all make! Even when I get custom design requests where the builder wants specific features, I still don't compromise safety. It's only happened one time where someone demanded something I wasn't willing to do. In that case I thanked him for his consideration and we parted ways. It's just not worth your reputation let alone someone's life. ---------------------------------------------------------------------------- ---- Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ |
Cape Fear Performance Report
I named it after the river basin. And hey, they might be honored to have
their boats named after mine. LOL! 98stratus wrote: You might want to be careful about marketing that as a "Cape Fear" design. Cape Fear Yachts might get a bit upset about you atemptingt o steal their trademark! "Matt Langenfeld" wrote in message nk.net... Excellent points. I don't want to put out anything that is risky. You get a feel what works and what doesn't so you can "copy-paste" some features. But there are many rules I self-impose on my designs to make sure things are safe, functional, reliable, and have a safety margins for those possible "oop's" we all make! Even when I get custom design requests where the builder wants specific features, I still don't compromise safety. It's only happened one time where someone demanded something I wasn't willing to do. In that case I thanked him for his consideration and we parted ways. It's just not worth your reputation let alone someone's life. ---------------------------------------------------------------------------- ---- Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ -- Matt Langenfeld JEM Watercraft http://jem.e-boat.net/ |
All times are GMT +1. The time now is 05:21 PM. |
Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 BoatBanter.com