The Marquis has a dubious manifold...
 

"Tim" wrote in message
...
On Jul 15, 7:31 pm, "mmc" wrote:
"Tim" wrote in message

...
On Jul 15, 10:26 am, "Harold" wrote:



"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the back
panel off to look for anything that myight need repairs, I noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB
Weld
over them and it held well, However I noticed that there is a bottom
crack where it seems the JB weld has cracked loose and I can see a
bit
of rust.

Due to aftermarke, the price of a lot of these items has really come
down to being reasonable. I probably ought to change out the
manifold
but it's a real bugger to take of where it sits. So, I'm going to
chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up.
And
the repair looks like it's held for quite a while, but is starting
to
fail.

Does anyone know of a better smear on product to seal the crack? Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets
---------.
That's a great addition! inner tube rubber is great stuff, can flash a patio
roof around palm trees or make a slingshot!

The Marquis has a dubious manifold...
 

On Jul 15, 8:38*pm, wrote:
On Thu, 15 Jul 2010 17:39:05 -0700 (PDT), Tim
wrote:



On Jul 15, 7:31*pm, "mmc" wrote:
"Tim" wrote in message

....
On Jul 15, 10:26 am, "Harold" wrote:

"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the back
panel off to look for anything that myight need repairs, I noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB Weld
over them and it held well, However I noticed that there is a bottom
crack where it seems the JB weld has cracked loose and I can see a bit
of rust.

Due to aftermarke, the price of a lot of these items has really come
down to being reasonable. I probably ought to change out the manifold
but it's a real bugger to take of where it sits. So, I'm going to chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up.. And
the repair looks like it's held for quite a while, but is starting to
fail.

Does anyone know of a better smear on product to seal the crack? Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets.

A beer box makes a pretty good gasket

True, but it doesn't wrap low pressure hoses very well, or at least I
dont' think they do.

Hmm, that reminds me

Duct Tape!

The Marquis has a dubious manifold...
 

In article m,
says...

"Tim" wrote in message
...
On Jul 15, 7:31 pm, "mmc" wrote:
"Tim" wrote in message

...
On Jul 15, 10:26 am, "Harold" wrote:



"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the back
panel off to look for anything that myight need repairs, I noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB
Weld
over them and it held well, However I noticed that there is a bottom
crack where it seems the JB weld has cracked loose and I can see a
bit
of rust.

Due to aftermarke, the price of a lot of these items has really come
down to being reasonable. I probably ought to change out the
manifold
but it's a real bugger to take of where it sits. So, I'm going to
chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up.
And
the repair looks like it's held for quite a while, but is starting
to
fail.

Does anyone know of a better smear on product to seal the crack? Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets
---------.
That's a great addition! inner tube rubber is great stuff, can flash a patio
roof around palm trees or make a slingshot!

Yeah, get a couple rolls of that plumbers tape they have on the tv
commercials for 9.99 for three rolls, "BUT WAIT"! IF YOU BUY NOW! Yup,
of all the crap on TV, that stuff works great, on a lot of stuff.

And a tube of "Shoe Goo" type adhesive too.. Stuff is as important as
ViceGrips, and Duct tape!

--
Rowdy Mouse Racing - We race for cheese!

The Marquis has a dubious manifold...
 

On Jul 15, 11:18*pm, wrote:
On Thu, 15 Jul 2010 18:58:04 -0700 (PDT), Tim
wrote:

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets.

A beer box makes a pretty good gasket

True, but it doesn't wrap low pressure hoses very well, or at least I
dont' think they do.

Hmm, that reminds me

Duct Tape!

Be sure you get the mil spec duct tape. It will hold up to water, heat
and pressure better than the drug store stuff.

Yessir. People dont' understand that there is a "good stuff" grade of
duct tape . Most people think it's all the same....

The Marquis has a dubious manifold...
 

On Jul 16, 6:15*am, I am Tosk wrote:
In article m,
says...





"Tim" wrote in message
....
On Jul 15, 7:31 pm, "mmc" wrote:
"Tim" wrote in message

....
On Jul 15, 10:26 am, "Harold" wrote:

"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the back
panel off to look for anything that myight need repairs, I noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB
Weld
over them and it held well, However I noticed that there is a bottom
crack where it seems the JB weld has cracked loose and I can see a
bit
of rust.

Due to aftermarke, the price of a lot of these items has really come
down to being reasonable. I probably ought to change out the
manifold
but it's a real bugger to take of where it sits. So, I'm going to
chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up.
And
the repair looks like it's held for quite a while, but is starting
to
fail.

Does anyone know of a better smear on product to seal the crack? Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets
---------.
That's a great addition! inner tube rubber is great stuff, can flash a patio
roof around palm trees or make a slingshot!

Yeah, get a couple rolls of that plumbers tape they have on the tv
commercials for 9.99 for three rolls, "BUT WAIT"! IF YOU BUY NOW! Yup,
of all the crap on TV, that stuff works great, on a lot of stuff.

And a tube of "Shoe Goo" type adhesive too.. Stuff is as important as
ViceGrips, and Duct tape!

--
Rowdy Mouse Racing - We race for cheese!

My brother mentioned that this simmer, Scott. Thanks for the
reminder....

The Marquis has a dubious manifold...
 

On Jul 16, 12:18*am, wrote:
On Thu, 15 Jul 2010 18:58:04 -0700 (PDT), Tim
wrote:

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets.

A beer box makes a pretty good gasket

True, but it doesn't wrap low pressure hoses very well, or at least I
dont' think they do.

Hmm, that reminds me

Duct Tape!

Be sure you get the mil spec duct tape. It will hold up to water, heat
and pressure better than the drug store stuff.

I didn't know about the mil spec stuff. Where does one buy that?

The Marquis has a dubious manifold...
 

In article 90187938-e865-4776-9f81-404564cb86a9
@j4g2000yqh.googlegroups.com, says...

On Jul 15, 8:38*pm, wrote:
On Thu, 15 Jul 2010 17:39:05 -0700 (PDT), Tim
wrote:



On Jul 15, 7:31*pm, "mmc" wrote:
"Tim" wrote in message

...
On Jul 15, 10:26 am, "Harold" wrote:

"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the back
panel off to look for anything that myight need repairs, I noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB Weld
over them and it held well, However I noticed that there is a bottom
crack where it seems the JB weld has cracked loose and I can see a bit
of rust.

Due to aftermarke, the price of a lot of these items has really come
down to being reasonable. I probably ought to change out the manifold
but it's a real bugger to take of where it sits. So, I'm going to chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up. And
the repair looks like it's held for quite a while, but is starting to
fail.

Does anyone know of a better smear on product to seal the crack? Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets.

A beer box makes a pretty good gasket

True, but it doesn't wrap low pressure hoses very well, or at least I
dont' think they do.

Hmm, that reminds me

Duct Tape!

No, no... Like I noted above. Get some of that silicone stretch tape
advertised on TV. Lowes also sells a version in the plumbing dept. The
stuff is GOLD. It only sticks to itself, and it does it well. You can
seal a high pressure hose while it is leaking and under pressure, or
seal just about anything in an emergency. This is not Teflon Plumbers
tape, or Electrical tape as a friend of mine insisted until I gave him a
roll (he was a lifetime boiler repair and fuel oil guy), just find a
roll and play around with it. Like I said, it's as necessary as
vicegrips, and duct tape... Once you try it, you won't go without it.
Well, get the duct tape too;)

--
Rowdy Mouse Racing - We race for cheese!

The Marquis has a dubious manifold...
 

On 7/16/10 8:19 AM, I am Tosk wrote:

it's as necessary as
vicegrips,

"Vicegrips" are what the police in Toskie's area will use to extricate
him from that tent. Home handymen there, however, will continue to use
Vise-Gripsâ„¢.

The Marquis has a dubious manifold...
 

On Fri, 16 Jul 2010 08:19:25 -0400, I am Tosk
wrote:

In article 90187938-e865-4776-9f81-404564cb86a9
, says...

On Jul 15, 8:38*pm, wrote:
On Thu, 15 Jul 2010 17:39:05 -0700 (PDT), Tim
wrote:



On Jul 15, 7:31*pm, "mmc" wrote:
"Tim" wrote in message

...
On Jul 15, 10:26 am, "Harold" wrote:

"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the back
panel off to look for anything that myight need repairs, I noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB Weld
over them and it held well, However I noticed that there is a bottom
crack where it seems the JB weld has cracked loose and I can see a bit
of rust.

Due to aftermarke, the price of a lot of these items has really come
down to being reasonable. I probably ought to change out the manifold
but it's a real bugger to take of where it sits. So, I'm going to chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up. And
the repair looks like it's held for quite a while, but is starting to
fail.

Does anyone know of a better smear on product to seal the crack? Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets.

A beer box makes a pretty good gasket

True, but it doesn't wrap low pressure hoses very well, or at least I
dont' think they do.

Hmm, that reminds me

Duct Tape!

No, no... Like I noted above. Get some of that silicone stretch tape
advertised on TV. Lowes also sells a version in the plumbing dept. The
stuff is GOLD. It only sticks to itself, and it does it well. You can
seal a high pressure hose while it is leaking and under pressure, or
seal just about anything in an emergency. This is not Teflon Plumbers
tape, or Electrical tape as a friend of mine insisted until I gave him a
roll (he was a lifetime boiler repair and fuel oil guy), just find a
roll and play around with it. Like I said, it's as necessary as
vicegrips, and duct tape... Once you try it, you won't go without it.
Well, get the duct tape too;)

You oughta send us each a roll so's we could try it.
--

John H

The Marquis has a dubious manifold...
 

--
"Political correctness is a doctrine, fostered by a delusional, illogical
minority, and rabidly promoted by an unscrupulous mainstream media, which
holds forth the proposition that it is entirely possible to pick up a turd
by the clean end."

"I am Tosk" wrote in message
...
In article m,
says...

"Tim" wrote in message
...
On Jul 15, 7:31 pm, "mmc" wrote:
"Tim" wrote in message

...
On Jul 15, 10:26 am, "Harold" wrote:



"Tim" wrote in message

...
On Jul 15, 9:11 am, "Harold" wrote:

"Tim" wrote in message

...

OK, so while I have the boat out in the sunlight and have the
back
panel off to look for anything that myight need repairs, I
noticed
that the previous owner muust have left water in the left exhaust
manifold and it froze and cracked. They have generous globs of JB
Weld
over them and it held well, However I noticed that there is a
bottom
crack where it seems the JB weld has cracked loose and I can see
a
bit
of rust.

Due to aftermarke, the price of a lot of these items has really
come
down to being reasonable. I probably ought to change out the
manifold
but it's a real bugger to take of where it sits. So, I'm going to
chip
away at the repair to see how sound it is.

this isn't a presurized system so there's not any steam build up.
And
the repair looks like it's held for quite a while, but is
starting
to
fail.

Does anyone know of a better smear on product to seal the crack?
Or
should I jsut bite it and buy a new manifold?

BITE!- Hide quoted text -

- Show quoted text -

Yeah, that's what I'm thinking. Running around a lake where you don't
have far to go to shore is one thing, being out on the Ohio River is
totally another.

Bit still. It wouldn't hurt to have a tube of 'something' on board to
try to make a quick fix if necessary.

It wouldn't hurt to carry some JB Weld and Marine Tex in your on
board
tool
kit.- Hide quoted text -

- Show quoted text -

Those are on the check list...
--------
Maybe a couple of oversized hose clamps and a hunk of gasket material?

I ahve an old car innertube folded up and tied. It fits in a small
space. Yes, either a person could use it for a float device (air
compressor on board) or with a box knife it can make some temporary
but ready gaskets
---------.
That's a great addition! inner tube rubber is great stuff, can flash a
patio
roof around palm trees or make a slingshot!

Yeah, get a couple rolls of that plumbers tape they have on the tv
commercials for 9.99 for three rolls, "BUT WAIT"! IF YOU BUY NOW! Yup,
of all the crap on TV, that stuff works great, on a lot of stuff.

And a tube of "Shoe Goo" type adhesive too.. Stuff is as important as
ViceGrips, and Duct tape!

--
Rowdy Mouse Racing - We race for cheese!

So what's in your tool kit. Hammer and 10 penny nails?