portable generator
 

How can I ground a 1000 watt Yamaha portable generator( EF1000is) to a
boat ?

portable generator
 

wrote in message
...
How can I ground a 1000 watt Yamaha portable generator( EF1000is) to a
boat ?


Why ??

--
Regards ........ Rheilly Phoull

portable generator
 

If this is for any purpose besides a temporary electric need like
powering Christmas lights for a one time boat parade I would suggest
rethinking your whole strategy.... or name me in your will....

portables and marine gensets have almost nothing in common, except the
fact that they both make power.

If it is for a one time activity on CALM water..... may I suggest you
put it on the SWIM platform (Fuel leaks can ruin your whole day... or
life) As far as grounding.... they usually have a grounding lug on them.
Just attach a wire from that lug to the ground of your boat. Not sure
why you would want to do that. you cannot combine power from multiple
gensets to power one large item. (Unless they are synced.... impossible
with a portable genset like you are talking about)




Rheilly Phoull wrote:

wrote in message
...

How can I ground a 1000 watt Yamaha portable generator( EF1000is) to a
boat ?



Why ??

portable generator
 

Please help me understand. MyYamaha manual says" be sure to ground (
earth) the generator" and the picture is showing a wire connected to the
generator and the other end is a nail burried to the earth ground. How
to I do that on a boat?
I have a 26 foot Monterey with shore power.I purchased a boat shore
power adapter to regular household plug ( 3 prong) and I was thingking
of pluging that to the generator. I am confuse about grounding of the
generator to the earth ground ( the nailing to ground thing) ????

portable generator
 

wrote in message
...
Please help me understand. MyYamaha manual says" be sure to ground (
earth) the generator" and the picture is showing a wire connected to the
generator and the other end is a nail burried to the earth ground. How
to I do that on a boat?
I have a 26 foot Monterey with shore power.I purchased a boat shore
power adapter to regular household plug ( 3 prong) and I was thingking
of pluging that to the generator. I am confuse about grounding of the
generator to the earth ground ( the nailing to ground thing) ????

Well you might be getting out of your depth a bit :-) but if the earth pin
of outlets on the generator are bonded to the neutral then the adaptor
should be OK. If not then the ground connection on the genny should be
conected to the earth on the board on your boat.
Since you seem a little unsure it might be safer to get a little
proffesional advice.
With regards to earthing on boats, it is a lot deeper than most are aware
and long term effects in the form of electrolysis can cause real damage.
If you are just going to bring the genny aboard now and then IMHO I would
not be too concerned about the earthing situation since the supply (The
genny) is independant from the mains and would be very much like "double
insulation" with regard to earth faults.


--
Regards ........ Rheilly Phoull

portable generator
 

On Sun, 18 Apr 2004 22:46:45 -0400, wrote:

Please help me understand. MyYamaha manual says" be sure to ground (
earth) the generator" and the picture is showing a wire connected to the
generator and the other end is a nail burried to the earth ground. How
to I do that on a boat?
I have a 26 foot Monterey with shore power.I purchased a boat shore
power adapter to regular household plug ( 3 prong) and I was thingking
of pluging that to the generator. I am confuse about grounding of the
generator to the earth ground ( the nailing to ground thing) ????

I have never understood that issue either. I have been on the edge of
buying a portable generator for several years, but never got around to
it because we rarely need it. Meanwhile I have been researching that
question on the net and in books like Nigel Calder for years too, and
never found a practical answer Surely there is a simple recipe for
non-electrrician boaters like us?

Our boat has an AC shore power 3-pronged inlet socket. We have a big
yellow 30-amp shore power cable, wihch of course we cannot use with a
portable generator like Romeoo's: such generators typically output
electricity through a normal household outdoor 3-pronged extension
cord. I have a 30-amp pigtail shorepower adapter that can be used to
adapt the household extension cord to the boat's shore power inlet
socket.

Our boat's AC wiring presumably is independent of the boat's DC
wiring. Or at least I certainly hope it is. The DC system's ground
is the battery/engine block. We have no "ground" to the ocean, nor
would I want stray current in the ocean around my boat.

Say I'm at anchor. If I put the generator on the swimdeck, run the
landlubber extention cord to the boat's AC input plug (with the
pigtail adapter), and turn on the generator, then where is ground? Is
it necessary to emulate the nail in the dirt, as if setup in a
campground when powering an RV?

Jim

portable generator
 

For short term use, you should be fine from a grounding point of view.
The round pin on the standard plug is the ground and that should carry
the ground to the boat. There are many other dangers here you should
consider that the grounding will not solve... including but not limited
to: Fuel issues, shock issues, CO issues, etc.

Jim Thompson wrote:
On Sun, 18 Apr 2004 22:46:45 -0400, wrote:


Please help me understand. MyYamaha manual says" be sure to ground (
earth) the generator" and the picture is showing a wire connected to the
generator and the other end is a nail burried to the earth ground. How
to I do that on a boat?
I have a 26 foot Monterey with shore power.I purchased a boat shore
power adapter to regular household plug ( 3 prong) and I was thingking
of pluging that to the generator. I am confuse about grounding of the
generator to the earth ground ( the nailing to ground thing) ????


I have never understood that issue either. I have been on the edge of
buying a portable generator for several years, but never got around to
it because we rarely need it. Meanwhile I have been researching that
question on the net and in books like Nigel Calder for years too, and
never found a practical answer Surely there is a simple recipe for
non-electrrician boaters like us?

Our boat has an AC shore power 3-pronged inlet socket. We have a big
yellow 30-amp shore power cable, wihch of course we cannot use with a
portable generator like Romeoo's: such generators typically output
electricity through a normal household outdoor 3-pronged extension
cord. I have a 30-amp pigtail shorepower adapter that can be used to
adapt the household extension cord to the boat's shore power inlet
socket.

Our boat's AC wiring presumably is independent of the boat's DC
wiring. Or at least I certainly hope it is. The DC system's ground
is the battery/engine block. We have no "ground" to the ocean, nor
would I want stray current in the ocean around my boat.

Say I'm at anchor. If I put the generator on the swimdeck, run the
landlubber extention cord to the boat's AC input plug (with the
pigtail adapter), and turn on the generator, then where is ground? Is
it necessary to emulate the nail in the dirt, as if setup in a
campground when powering an RV?

Jim

portable generator
 

Thanks for the reply. Fuel, CO and other non-electrical issues aside,
what did you mean by shock issues? And how does the round pin carry
the ground to the boat, if the boat is fibreglass, sitting on water,
and the generator is connected to the boat's shore power plug with a
3-wire shore power cable? Where does that round pin ground lead to?
Thank you for any insights you can provide to this issue.

Jim

On Tue, 20 Apr 2004 22:19:33 -0400, Ed wrote:

For short term use, you should be fine from a grounding point of view.
The round pin on the standard plug is the ground and that should carry
the ground to the boat. There are many other dangers here you should
consider that the grounding will not solve... including but not limited
to: Fuel issues, shock issues, CO issues, etc.

Jim Thompson wrote:
On Sun, 18 Apr 2004 22:46:45 -0400, wrote:
Please help me understand. MyYamaha manual says" be sure to ground (
earth) the generator" and the picture is showing a wire connected to the
generator and the other end is a nail burried to the earth ground. How
to I do that on a boat?
I have a 26 foot Monterey with shore power.I purchased a boat shore
power adapter to regular household plug ( 3 prong) and I was thingking
of pluging that to the generator. I am confuse about grounding of the
generator to the earth ground ( the nailing to ground thing) ????

I have never understood that issue either. I have been on the edge of
buying a portable generator for several years, but never got around to
it because we rarely need it. Meanwhile I have been researching that
question on the net and in books like Nigel Calder for years too, and
never found a practical answer Surely there is a simple recipe for
non-electrrician boaters like us?

Our boat has an AC shore power 3-pronged inlet socket. We have a big
yellow 30-amp shore power cable, wihch of course we cannot use with a
portable generator like Romeoo's: such generators typically output
electricity through a normal household outdoor 3-pronged extension
cord. I have a 30-amp pigtail shorepower adapter that can be used to
adapt the household extension cord to the boat's shore power inlet
socket.

Our boat's AC wiring presumably is independent of the boat's DC
wiring. Or at least I certainly hope it is. The DC system's ground
is the battery/engine block. We have no "ground" to the ocean, nor
would I want stray current in the ocean around my boat.

Say I'm at anchor. If I put the generator on the swimdeck, run the
landlubber extention cord to the boat's AC input plug (with the
pigtail adapter), and turn on the generator, then where is ground? Is
it necessary to emulate the nail in the dirt, as if setup in a
campground when powering an RV?

portable generator
 

All metal (on most boats) is bonded together (green wires). This
includes the outdrives, shafts, thru-hulls etc. The bonding wire is
usually connected to ship's ground (Negative battery) and to the Green
side of the 110/220 sytem. SOMETIMES... there is a device that sits in
the middle to help save your zincs in areas with lots of current in the
water... this aside... the Ground wire on your shorepower is connected
to the bonding system.

As far as shock issues... if you touch a hot wire... or are on the swim
platform when a wave hits you and the generator... or if the plug gets
wet and you touch it (or any number of things...) you will get
shocked.... GFIs help but will not eliminate the issue.

Ed





Jim Thompson wrote:
Thanks for the reply. Fuel, CO and other non-electrical issues aside,
what did you mean by shock issues? And how does the round pin carry
the ground to the boat, if the boat is fibreglass, sitting on water,
and the generator is connected to the boat's shore power plug with a
3-wire shore power cable? Where does that round pin ground lead to?
Thank you for any insights you can provide to this issue.

Jim

On Tue, 20 Apr 2004 22:19:33 -0400, Ed wrote:


For short term use, you should be fine from a grounding point of view.
The round pin on the standard plug is the ground and that should carry
the ground to the boat. There are many other dangers here you should
consider that the grounding will not solve... including but not limited
to: Fuel issues, shock issues, CO issues, etc.

Jim Thompson wrote:

On Sun, 18 Apr 2004 22:46:45 -0400, wrote:

Please help me understand. MyYamaha manual says" be sure to ground (
earth) the generator" and the picture is showing a wire connected to the
generator and the other end is a nail burried to the earth ground. How
to I do that on a boat?
I have a 26 foot Monterey with shore power.I purchased a boat shore
power adapter to regular household plug ( 3 prong) and I was thingking
of pluging that to the generator. I am confuse about grounding of the
generator to the earth ground ( the nailing to ground thing) ????

I have never understood that issue either. I have been on the edge of
buying a portable generator for several years, but never got around to
it because we rarely need it. Meanwhile I have been researching that
question on the net and in books like Nigel Calder for years too, and
never found a practical answer Surely there is a simple recipe for
non-electrrician boaters like us?

Our boat has an AC shore power 3-pronged inlet socket. We have a big
yellow 30-amp shore power cable, wihch of course we cannot use with a
portable generator like Romeoo's: such generators typically output
electricity through a normal household outdoor 3-pronged extension
cord. I have a 30-amp pigtail shorepower adapter that can be used to
adapt the household extension cord to the boat's shore power inlet
socket.

Our boat's AC wiring presumably is independent of the boat's DC
wiring. Or at least I certainly hope it is. The DC system's ground
is the battery/engine block. We have no "ground" to the ocean, nor
would I want stray current in the ocean around my boat.

Say I'm at anchor. If I put the generator on the swimdeck, run the
landlubber extention cord to the boat's AC input plug (with the
pigtail adapter), and turn on the generator, then where is ground? Is
it necessary to emulate the nail in the dirt, as if setup in a
campground when powering an RV?

portable generator
 

On Thu, 22 Apr 2004 05:22:45 GMT, WaIIy
wrote:

I always heard you NEVER mix the AC and DC ground together. Never.
Of course, I'd like to know if this is true, but it makes a lot of sense
not to.

I was under the same impression. I thought that my AC system was
grounded through the shore power plug to the 3-wire system ashore.

Here is my rudimentary understanding:
http://jimthompson.net/boating/Elect...lectronics.htm

Jim

portable generator
 

I always heard you NEVER mix the AC and DC ground together. Never.

Of course, I'd like to know if this is true, but it makes a lot of sense
not to.

You guys have bumped into the "green wire controversy". Some "authorities"
say you should not connect AC and DC systems. Charles Payne is of this
opinion in his book. I'm not sure, but I think Nigel Calder also thinks its
a bad idea. On the other hand I think Dave Gerr recently had an article in
Sail or Cruising World in which he said they should be connected together.
I think this may also be the current ABYC recommendation. The rational is
that if you somehow get 110V AC into your DC system you can be electrocuted
by touching the DC if it has no earth ground. Personally I think the
chances of getting AC into my DC system are so low that I intend to leave my
systems as the original manufacturer installed them, ie. separate.

"WaIIy" wrote in message
...
On Wed, 21 Apr 2004 19:37:43 -0400, Ed wrote:

All metal (on most boats) is bonded together (green wires). This
includes the outdrives, shafts, thru-hulls etc. The bonding wire is
usually connected to ship's ground (Negative battery) and to the Green
side of the 110/220 sytem. SOMETIMES... there is a device that sits in
the middle to help save your zincs in areas with lots of current in the
water... this aside... the Ground wire on your shorepower is connected
to the bonding system.

As far as shock issues... if you touch a hot wire... or are on the swim
platform when a wave hits you and the generator... or if the plug gets
wet and you touch it (or any number of things...) you will get
shocked.... GFIs help but will not eliminate the issue.

Ed


I always heard you NEVER mix the AC and DC ground together. Never.

Of course, I'd like to know if this is true, but it makes a lot of sense
not to.

portable generator
 

Yes, there is lots of info out there.
In my original post I mentioned Charles Payne. Actually the name is John C.
Payne and the book is "Boat Owners Electrical and Electronics Bible". He is
against connecting the two systems. This is a fairly old book though.
I checked my Nigel Calder books and he basically points out the benefits and
the problems. He concludes that you shouldn't connect the systems unless
you use a galvanic isolator or isolation transformer.
I suppose before galvanic isolators became readily available the general
consensus was to leave these two systems unconnected. Adding the isolator
and grounding the AC system to the DC system gives you some extra safety
provided the isolator and its circuit continues to function as intended so I
guess the current thinking is to go this route.

"WaIIy" wrote in message
...
On Thu, 22 Apr 2004 19:36:29 GMT, "Gordon Wedman"
wrote:

I always heard you NEVER mix the AC and DC ground together. Never.

Of course, I'd like to know if this is true, but it makes a lot of
sense
not to.

You guys have bumped into the "green wire controversy". Some
"authorities"
say you should not connect AC and DC systems. Charles Payne is of this
opinion in his book. I'm not sure, but I think Nigel Calder also thinks
its
a bad idea. On the other hand I think Dave Gerr recently had an article
in
Sail or Cruising World in which he said they should be connected
together.
I think this may also be the current ABYC recommendation. The rational
is
that if you somehow get 110V AC into your DC system you can be
electrocuted
by touching the DC if it has no earth ground. Personally I think the
chances of getting AC into my DC system are so low that I intend to leave
my
systems as the original manufacturer installed them, ie. separate.

Thanks for the info. I found a bit of stuff....

AC Ground
See Practical Sailor August 15, 1995 for a detailed treatment of the
green wire. The best solution is a heavy and expensive isolation
transformer. The acceptable solution (for the rest of us) is to install
a light and inexpensive Galvanic Isolator in the green wire, between the
shorepower cord socket on your boat, and the connection to the boat's AC
panel. Then, connect the grounding conductor (green) of the AC panel
directly to the engine negative terminal or its bus. Note that this
meets ABYC's recommendations. In choosing Galvanic Isolators, make sure
that you select one that has a continuous current rating that is at
least 135% the current rating on the circuit breaker on your dock box.
Certain Galvanic Isolators (e.g. Quicksilver) include large capacitors
in parallel with the isolation diodes, which in certain situations
theoretically provide better galvanic protection. Unfortunately, these
units cost substantially more than conventional Galvanic Isolators. If
you feel like spending real money on galvanic isolation, you might as
well do it right and buy an isolation transformer.