Sail-powered SWATH catamaran
 

Several navies have introduced SWATH catamarans and found benefits like
high speed, stability, and fuel efficiency. Worthwhile advantages, yet
no sailing versions of the SWATH concept seem to have emerged. Anyone
know of any examples sailing anywhere?
Reducing the scale of these military vessels down to regular sailboat
sizes would create a very tender boat since each hull would be only 50%
buoyant. So beefing up to perhaps 100% in each hull would be a first
design step. Apart from this pre-requisite, I see no serious drawbacks
to creating a superior performance and wave-piercing catamaran.
Anyone care to differ, ... or offer further design refinements that
might help make this the catamaran of the future ?

SailNut.

Sail-powered SWATH catamaran
 

I see no serious drawbacks
to creating a superior performance and wave-piercing catamaran.

Somehow wave piercing and sails aloft seems pretty unlikely combination.

Sail-powered SWATH catamaran
 

wrote

I see no serious drawbacks

That's why you have no business taking such an idea beyond idle
chatter and daydreaming. Seeing the drawbacks and figuring out how to
work around them is the essence of developing new technologies.

--

Roger Long

Sail-powered SWATH catamaran
 

wrote:
Several navies have introduced SWATH catamarans and found benefits like
high speed, stability, and fuel efficiency. Worthwhile advantages, yet
no sailing versions of the SWATH concept seem to have emerged. Anyone
know of any examples sailing anywhere?
Reducing the scale of these military vessels down to regular sailboat
sizes would create a very tender boat since each hull would be only 50%
buoyant. So beefing up to perhaps 100% in each hull would be a first
design step. Apart from this pre-requisite, I see no serious drawbacks
to creating a superior performance and wave-piercing catamaran.
Anyone care to differ, ... or offer further design refinements that
might help make this the catamaran of the future ?

SailNut.

The Swath design doesn't look like a good match to sailboats. Wave
piercing has been used, though the most famous case was not a great
success:
http://www.solarnavigator.net/team_phillips.htm

Sail-powered SWATH catamaran
 

wrote in message
ups.com...
Several navies have introduced SWATH catamarans and found benefits like
high speed, stability, and fuel efficiency. Worthwhile advantages, yet
no sailing versions of the SWATH concept seem to have emerged. Anyone
know of any examples sailing anywhere?
Reducing the scale of these military vessels down to regular sailboat
sizes would create a very tender boat since each hull would be only 50%
buoyant. So beefing up to perhaps 100% in each hull would be a first
design step. Apart from this pre-requisite, I see no serious drawbacks
to creating a superior performance and wave-piercing catamaran.
Anyone care to differ, ... or offer further design refinements that
might help make this the catamaran of the future ?

SailNut.


I suspect that the required size and strength of the rigging would prohibit
the success of a SWATH cat. Fully submerged hulls would have serious mass,
requiring a LOT of force to move. Further, the vessel remaining more or less
stationary relative to pitch and roll would mean that wind forces could not
be spilled by heeling -- not even to the (relatively) limited extent of
regular catamarans. So I envision ever-increasing sailplans requiring
ever-more-massive rigs to control them spiraling ever-outwards until the
physical structure of the vessel itself is incapable of containing them, all
just to travel slower than a rowboat.

Sail-powered SWATH catamaran
 

...So I envision ever-increasing sailplans requiring
ever-more-massive rigs to control them spiraling ever-outwards until the
physical structure of the vessel itself is incapable of containing them, all
just to travel slower than a rowboat.

I think you're right. I made some napkin calculations (and did a
little mitchlet modeling) on this idea seven years ago and came pretty
much to the conclusion that you'd need to do something pretty radical
to make a true swath cat move in light air. The wetted surface is what
really does one in. A friend of mine did a compromise design with very
long bulbs down in New Zealand and he was happy with her, but she was
always a motor sailer and is being refit to be a mostly motor whale
watching platform. The real advantage of swath is that it makes sea
kind boats. At some speeds they may also be efficient but only where
wave drag dominates and only if you can get the displacement far from
the surface. I've noticed with the local swath boat (Navtec) that they
create a pretty energetic wave train, but she's a comfy boat in most
weather. As others have noted you'll also need to think a bit about
stability if using sail plans that have a heeling moment (really big
kites might work). Foils plus some kind of reserve bouncy (ie. hulls
near the surface) seemed likely candidates to me but both add drag.
There were lots of other issues with making the thing work and making
it maintainable (eg. access to the hulls, control surface linkages
&c.). And it would be a bugger to build and expensive... Seems like
the kind of boat project that keeps folks from getting out and
cruising...

-- Tom.

Sail-powered SWATH catamaran
 

Sail-powered SWATH catamaran
 

Sail-powered SWATH catamaran
 

As far as CRUISING goes, who cares.

Why not try the site: rec.boats.misc.not.relevant.cruising

or

rec.boats.starshipenterprise.vulcan.cruising

Cap'n Ric
S/V Sezaneh

Sail-powered SWATH catamaran
 

Sail-powered SWATH catamaran
 

Thank you everyone for all the responses, and humor, and a special
thanks to Jeff for the Team Philips link.
Definitely a thumbs-down response to my suggestion. I agree it is an
unusual combination. Perhaps I should have emphasized the wave-piercing
aspect rather than make mention of SWATH.

I'll try and explain further. Reserve buoyancy is important of course,
but it is a handicap when a large amount of that buoyancy has to be
pushed thru the water. By dedicating only an adequate/optimal amount of
reserve buoyancy to the hulls (let's call them amas) allows them to
efficiently do the tasks they are intended to perform, i.e. stay afloat
and progress thru the water. For a limited class of vessels, I believe
it is possible to make a better arrangement without pushing empty
buoyancy thru the water, and thus improve performance. Such a vessel
might be a coastal cruiser. Hence my post in this forum.

My suggestion was for 100% buoyancy per ama, providing 200% of the
total displacement of the boat, this being adequate (just) and still
confers stability and sea-kindliness. Elevating the main hull by 5 or 6
feet and in a central location provides the remainder of the reserve
buoyancy (but only when the vessel finds itself in conditions that need
it).

Here's a very basic schematic:
m
m
Side view: a ----------------
a
s cabin
s
t ----------------
t

2 amas - 0000000000000000000000000000000000000000000000


Because the buoyancy in the amas is minimal but adequate, the wetted
surface area of the amas combined is not excessive. Consider each ama
as a 3 ft diameter "cylindrical" at 80 ft long, with little rocker, and
50% immersion, equates to approx 750 sq ft wetted surface. This is
only marginally more than an 80 ft monohull (670 sq ft) but its 60+ sq
ft keel makes them almost equivalent in this regard. So wetted surface
area should not be a drawback (in this length range).
Total buoyancy for these amas amounts to 16+16 = 32 tonnes. This
allows an operating displacement around 15 tonnes, allocated equally to
amas and cabin contents/superstructure (5T each), thus keeping CG low
(but 4 ft above water). Frontal area is a mere 6 sq ft per ama, making
an excellent wave-piercer. This is quite an improvement over say a
similar catamaran, since less water is pushed aside and the shortest
distance is thru the waves, not over them.
Lateral resistance of the amas amounts to over 160 sq ft, and although
shallow, there should be little need for a keel. (This also makes for
good directional stability, though could present some difficulty in
turning). Two masts perhaps, allowing smaller sails for easier
handling by crew.

Thanks again,
Sailnut


On Oct 24, 9:53 pm, DSK wrote:
wrote:
Reducing the scale of these military vessels down to regular sailboat
sizes would create a very tender boat since each hull would be only 50%
buoyant. So beefing up to perhaps 100% in each hull would be a first
design step.??
Please explain further. Perhaps you mean the reduced volume
available for reserve bouyancy?

Apart from this pre-requisite, I see no serious drawbacks
to creating a superior performance and wave-piercing catamaran.You don't think that the lack of reserve bouyancy, and the
concomitant stability, is a "serious" drawback? Everybody
else does.

Fresh Breezes- Doug King

Sail-powered SWATH catamaran
 

...Perhaps I should have emphasized the wave-piercing
aspect rather than make mention of SWATH. ...

A narrow water plane and light weight are key to high speed in
catamarans. The A class cats have been leading the way in very low
volume, very fine hull shapes. They are very much wave piercing
designs. The new C class "Object 2" by Steve Killing is a good example
of the current state of the art in this. Many cruising cats have been
designed with very fine bows and narrow water planes often expanding at
a distinct chine to get reasonable volume in the living spaces. Some
have even had wave true wave-piercing bows extending beyond the main
hulls. However, the trend in dedicated cruising boats has been to
towards wider, simpler hulls. When Alexander Simonis was designing the
Moorings 4500 he did a study and found that Fn's rarely exceeded 0.6 in
the cruising fleet and concluded that ideal cruising cat hulls should
place more emphasis on wetted surface and load carrying and less on
wave drag. His hulls ended up being around 1:8 length to beam and
quite full and round. The advantages of simple tooling, high volume
and good load carrying are hard to argue against in a dedicated
cruiser. In the racing fleet very light, slender, wave piercing hulls
have proven themselves. Sadly, there seems to be comparatively little
demand for cat designs that take the middle ground.

-- Tom.

Sail-powered SWATH catamaran
 

cool ideas, guys, very interesting considerations. Here's something I'd
love to get your input on. (tsmwebb: no way this swath is slow!)
Remember the crossbow/sling design thing, water speed record... years
ago. Bill, submergence gives stability. Sailnut is right, if dimensions
work. Thanks, Q

It's pretty clear that swath design parameters focus mainly on
submergence, buoyancy, drag and obviously wave amplitude
considerations. What are best design considerations for max. wave
amplitude? Somebody must have figured that one out. Certainly in all
the literature available, there should be design parameters which
define how high the main hull rides above the lowest possible draft.
This, then should offer guidelines for ideal beam to draft to length
parameters, right?

So, what if we turn this design-configuring swath definition around?
What is the ideal beam to draft to length oa, for an ocean-going, sail
powered swath cat? Oh, if only Hobie could be here!

Then I'd like to use this to scale relationship to size a new hull
design to the max. allowable strength parameters of the construction
materials proposed. Submerged, aluminum, or steel construction
(ballast) with a composite carbon fiber and stressed-skin membrane hull
design above water, for weight/mass reduction. Stressed membrane maximum
shear strength should provide an ideal maximum dimensional size of such
a vessel. Now a bunch of you are scratching your heads going: wow....

Got any suggestions? Here's mine:

LOA: 145-160 ft
Beam: 48 ft (yeowsa...)
Draft: 16 ft DW, 6 ft- littoral
clear-to-hull air plane: 6ft-16ft
Mast (s) Hgt. 180-220 ft. (depends upon geom. config.)
usable deck/main hull: Loa: 110 ft., beam: 36 ft, height 16 ft

obvious secondary propulsion systems are diesel/electric, in pontoons.
With the large surface area of such a design, eco-PV solar panels and
rigid wing composite sails for a quad, cross-braced mast system is
proposed

In the luxury, gigayacht designs I have yet to see anyone suggest this.
I understand the probs with cats, structural torsion, cantilever, huge
moment arm loads, and obviously beam width in harbors, (who'd want to
come in?) but it seems that for ideal ocean going stability, platform
area and largest sail/mast design configurations, this kind of swath
cat design has huge advantages.

There are two other parameters in the initial design configuration
layout I'd like to propose for this kind of radical design:

1. Adjustable draft depth, swing/hinged, or hydraulic/telescopic
pontoons, or
2. air-inflated, water ballast rigid structure pontoons.

i.e. when shallow draft required, submerged pontoons are air buoyed,
raising entire structure higher off water plane. With conditions of
deep water sailing, pontoons are partially ballasted with water, the
inherent structural mass increase of pontoons adding stability and
inertia-resisting wave modulation under high yield wind conditions.

As in any sailboat, less mass is better for increased performance. With
the moment arm of a large beam, huge mast lengths and max sail areas can
be achieved. What are the limiting factors for such a design?
Manoeuverability? Turn radii, ouch?

I assume the optimum hydro-dynamic submerged pontoon shapes, scaled,
will be the Ohio class boomer sub hull shapes. Put enough money into
those shapes, no?

So, where are my major probs? I need a big job to get this started.
LOL!


--
Qhiron
Message Origin: TRAVEL.com