BoatBanter.com

BoatBanter.com (https://www.boatbanter.com/)
-   Boat Building (https://www.boatbanter.com/boat-building/)
-   -   question fuel polishing brass bronze whatever piping adhesive (https://www.boatbanter.com/boat-building/86913-question-fuel-polishing-brass-bronze-whatever-piping-adhesive.html)

Bill Bligh October 9th 07 03:05 PM

question fuel polishing brass bronze whatever piping adhesive
 
Trying to assemble a diesel fuel polishing device from filters,
pipes ( nipples ), gauges, magnet, a pump, hoses and many
valves.

Loctite 242 used by one manufacturer, Loctite 55 sold
for the purpose by plumbing supply company. The usual
sodden wharf rat layabouts urge teflon tape - but every
article or book which mentions teflon tape and diesel
fuel warn against the stuff - use the engine as a mooring
after using teflon...

Guess I will be calling polisher manufacturers asking
what they use. And, possibly L55 lockd nipple and fitting
in a jar of diesel fora week or two?

Would have been cheaper and a lot less painful to have
bought a small commercially bult polisher. A lot cheaper!

One mo marine looking ball valves such as the full size
1/4 NPT valves from "Apollo," are they OK for marine
use carrying diesel?

Thanks,

Bligh

Lew Hodgett October 9th 07 04:39 PM

question fuel polishing brass bronze whatever piping adhesive
 

"Bill Bligh" wrote:

Trying to assemble a diesel fuel polishing device from filters,
pipes ( nipples ), gauges, magnet, a pump, hoses and many
valves.

Loctite 242 used by one manufacturer, Loctite 55 sold
for the purpose by plumbing supply company. The usual
sodden wharf rat layabouts urge teflon tape - but every
article or book which mentions teflon tape and diesel
fuel warn against the stuff - use the engine as a mooring
after using teflon...

snip

Teflon TAPE is to be avoided on ALL fuel systems since bits of it will
break off and eventually plug the nozzle orifices of the fuel systems.

Use teflon paste type joint compounds.

Personally, I like bronze ball valves with S/S hardware along with
Racor filters, but YMMV.

Have fun.

Lew



Matt Colie[_2_] October 9th 07 04:44 PM

question fuel polishing brass bronze whatever piping adhesive
 
Bill,
(Any relation to William Bligh?)
I am a licensed ship's engineer and have a few other credits that
apply here and I an going to answer quite a few of your questions in
line - I don't like this, but it will work best here.

Bill Bligh wrote:
Trying to assemble a diesel fuel polishing device from filters,
pipes ( nipples ), gauges, magnet, a pump, hoses and many
valves.

Loctite 242 used by one manufacturer, Loctite 55 sold
for the purpose by plumbing supply company. The usual
sodden wharf rat layabouts urge teflon tape - but every
article or book which mentions teflon tape and diesel
fuel warn against the stuff - use the engine as a mooring
after using teflon...

The problem is not the teflon as a material. It is good.
Problem with teflon tape is multifaceted. It does not do well with
steel fitting (often used in diesel fuel systems) - because die cut
threads often have burns that tear up the tape, it balls up in the joint
and makes a solid seal hard to get. If tape is wrapped on in the wrong
direction, it will possibly ball - again. If tape is wrapped over the
end of the male thread so it is exposed, pieces may get knocked loose
and carried downstream and cause all manner of grief (probably the cause
of the engine reference) as the working clearances in diesel fuel
systems are very tight. Tape may also end up exposed if the wrapped
portion extended through the fitting it is threaded into - same-same.

Guess I will be calling polisher manufacturers asking
what they use. And, possibly L55 locked nipple and fitting
in a jar of diesel for a week or two?

L55 is a thread of stuff you wrap around the male fitting (as I recall),
it can't be much different than teflon tape.

Would have been cheaper and a lot less painful to have
bought a small commercially built polisher. A lot cheaper!

But you will have one that works the way you want.

One mo marine looking ball valves such as the full size
1/4 NPT valves from "Apollo," are they OK for marine
use carrying diesel?

Apollo used to be a good manufacturer. You will have to get a material
list for the specific valve you are planning to buy. If it is bronze,
stainless steel and teflon - yeah, it's good.

Thanks,

Bligh

Good Luck Guy
Matt Colie
Lifelong Waterman and Licensed Mariner

[email protected] October 9th 07 06:48 PM

question fuel polishing brass bronze whatever piping adhesive
 
Preferred thread sealant is 'TFE liquid pipe thread sealant with
Teflon'.

See: http://www.go2marine.com/product.do?no=94759F

MW


Dan October 9th 07 09:18 PM

question fuel polishing brass bronze whatever piping adhesive
 

Loctite 567 is the best stuff in the world. Put some on a thread and
screw it together hand tight. Won't come loose tomorrow without wrenches.


All times are GMT +1. The time now is 02:59 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 BoatBanter.com