Polyurethane paint
 

Someone told me it won't adhere to to epoxy. True or false?
Thanks
Gordon

Polyurethane paint
 

Gordon wrote:
Someone told me it won't adhere to to epoxy. True or false?

You shoot high build primer first, then L/P.

Lew

Polyurethane paint
 

Flase.

Both one and two part polyurethanes are great finishes over epoxy
substrates *provided* there is no remaining 'amine blush.'
Manufacturers of PU (like Interlux) have all developed a 'tie coat' or
'primer' to isolate the epoxy sustrate from the overcoating paint.
Here's what Interlux says:

"Be sure to use Epoxy Barrier-Kote 404/414 over clear epoxy to prevent
blush from affecting drying and adhesion of Brightside".

MW

Polyurethane paint
 

I have another question about polyurethane paint. After priming the
epoxy and using a poly paint would it be lighter in weight than gel
coat finish and more fade resistant. The weight issue is important
because I'm using it on a canoe.
wrote:
Flase.

Both one and two part polyurethanes are great finishes over epoxy
substrates *provided* there is no remaining 'amine blush.'
Manufacturers of PU (like Interlux) have all developed a 'tie coat' or
'primer' to isolate the epoxy sustrate from the overcoating paint.
Here's what Interlux says:

"Be sure to use Epoxy Barrier-Kote 404/414 over clear epoxy to prevent
blush from affecting drying and adhesion of Brightside".

MW

Polyurethane paint
 

I think we're talking ablout two different construction methods...
"Gelcoat" generally implies female mold, fiberglass laminate
construction with polyester resins, where the colored gelcoat is
applied against a release agent, (preventing the gelcoat from sticking
to the mold) followed by a few to many-many layers of fiberglass of
various weaves & thickness. Here, the 'color' is the *first* item to
be applied (against the female mold).

"Paint" is generally used in male mold construction, mostly used in
"one-off" boat building. (Paint is also used over "old gelcoat" after
it has faded after years of sun/abuse/neglect). In M-M construction,
various materials (cold-molded wood, sheet "foam", fiberglass planking)
are laid over a male mold with the hull thickness then laminated up
(often using epoxy resins) with either additional wood veniers, woven
or knitted fiberglass, kevlar, carbon fiber or what-have-you.
Here, the paint (color) is applied *last*, against a primer that acts
as an adhesion base for the paint as well as a barrier against any
epoxy 'blush'.

As to the weight: One applies Polyurethane paint in multiple (like 3)
*very* thin coats. I'd guess you could do a canoe with about a quart
of paint / solvent / reducer which might weigh (guessing) about 2 lbs
(total).

MW
Los Angeles

Polyurethane paint
 

If Gelcoat is used in a female mold then no filler / fairing should be
required.
If paint is used over glass then usually some amount of filler and fairing
would be required.
The weight of filler under the pain should easily exceed the total weight of
gelcoat.

Having said that I wouldn't think that the weight difference between gelcoat
and painting would be significant enough to worry about and it would be
pretty difficult to accurately calculate. If painting so much would depend
on technique.

wrote in message
ups.com...
I think we're talking ablout two different construction methods...
"Gelcoat" generally implies female mold, fiberglass laminate
construction with polyester resins, where the colored gelcoat is
applied against a release agent, (preventing the gelcoat from sticking
to the mold) followed by a few to many-many layers of fiberglass of
various weaves & thickness. Here, the 'color' is the *first* item to
be applied (against the female mold).

"Paint" is generally used in male mold construction, mostly used in
"one-off" boat building. (Paint is also used over "old gelcoat" after
it has faded after years of sun/abuse/neglect). In M-M construction,
various materials (cold-molded wood, sheet "foam", fiberglass planking)
are laid over a male mold with the hull thickness then laminated up
(often using epoxy resins) with either additional wood veniers, woven
or knitted fiberglass, kevlar, carbon fiber or what-have-you.
Here, the paint (color) is applied *last*, against a primer that acts
as an adhesion base for the paint as well as a barrier against any
epoxy 'blush'.

As to the weight: One applies Polyurethane paint in multiple (like 3)
*very* thin coats. I'd guess you could do a canoe with about a quart
of paint / solvent / reducer which might weigh (guessing) about 2 lbs
(total).

MW
Los Angeles

Polyurethane paint
 

Douglas wrote:
I have another question about polyurethane paint. After priming the
epoxy and using a poly paint would it be lighter in weight than gel
coat finish and more fade resistant. The weight issue is important
because I'm using it on a canoe.
wrote:
Flase.

Both one and two part polyurethanes are great finishes over epoxy
substrates *provided* there is no remaining 'amine blush.'
Manufacturers of PU (like Interlux) have all developed a 'tie coat' or
'primer' to isolate the epoxy sustrate from the overcoating paint.
Here's what Interlux says:

"Be sure to use Epoxy Barrier-Kote 404/414 over clear epoxy to prevent
blush from affecting drying and adhesion of Brightside".

MW


Gelcoat is heavier guaranteed. It's a thick coloured resin layer vs.
thin polyurethane paint.

Evan Gatehouse

Polyurethane paint
 

Gordon wrote:

Someone told me it won't adhere to to epoxy. True or false?
Thanks
Gordon




epoxy is the common primer under two part poly (LPU) coatings.

paul oman
progressive epoxy polymers.