waterproof shaft seal?
 

I am trying to waterproof a small electric motor (submerged) so that
shaft will be sticking out of waterproof enclosure. Can anyone point
me to a source of water sealed bushings or bearings for this sort of
application? I have been looking all over the net and can't seem to
come up with ideas or supplies to do this. The shaft size will be =
1/4"

Thanks!
Bailey--

waterproof shaft seal?
 

The problem here is shaft size: it's way too small for our boats and you
will not find a shaft seal in the boating supplies field.
How about industrial supplies? Shaft seals are used in all kind of tanks.


--
Jacques
http://www.bateau.com

"MBS" wrote in message
m...
I am trying to waterproof a small electric motor (submerged) so that
shaft will be sticking out of waterproof enclosure. Can anyone point
me to a source of water sealed bushings or bearings for this sort of
application? I have been looking all over the net and can't seem to
come up with ideas or supplies to do this. The shaft size will be =
1/4"

Thanks!
Bailey--

waterproof shaft seal?
 

Don't know which country you are in but check out your ag dealers. I reckon
they will have one to fit your purpose from one of those high pressure
chemical hand sprayers. In Australia look up Hardie.
Brumer


"Jacques Mertens" wrote in message
...
The problem here is shaft size: it's way too small for our boats and you
will not find a shaft seal in the boating supplies field.
How about industrial supplies? Shaft seals are used in all kind of tanks.


--
Jacques
http://www.bateau.com

"MBS" wrote in message
m...
I am trying to waterproof a small electric motor (submerged) so that
shaft will be sticking out of waterproof enclosure. Can anyone point
me to a source of water sealed bushings or bearings for this sort of
application? I have been looking all over the net and can't seem to
come up with ideas or supplies to do this. The shaft size will be =
1/4"

Thanks!
Bailey--

waterproof shaft seal?
 

In my experience submerged motors ( as used in submersible pumps) are to
be avoided if at all possible. And for a one-off design, you are putting a
lot of effort into something which will ultimately be unproven and a
potential failure point. You did not say what you are trying to achieve,
power, RPM, depth of submergence, fresh or salt .... Or what you have
available by way of power sources.
Can you go to a flexible shaft and keep the motor above the water? Can you
use pneumatics or hydraulics or a water driven system? What about a
magnetic drive? These are often used on pumps for severe chemical duty to
eliminate the seal problems.
Failing that, I think you are up for an expensive mechanical seal.

David



But I'd look at other ways of doing the job if at all possible.
"BruceM" wrote in message
...
Don't know which country you are in but check out your ag dealers. I
reckon
they will have one to fit your purpose from one of those high pressure
chemical hand sprayers. In Australia look up Hardie.
Brumer


"Jacques Mertens" wrote in message
...
The problem here is shaft size: it's way too small for our boats and you
will not find a shaft seal in the boating supplies field.
How about industrial supplies? Shaft seals are used in all kind of
tanks.


--
Jacques
http://www.bateau.com

"MBS" wrote in message
m...
I am trying to waterproof a small electric motor (submerged) so that
shaft will be sticking out of waterproof enclosure. Can anyone point
me to a source of water sealed bushings or bearings for this sort of
application? I have been looking all over the net and can't seem to
come up with ideas or supplies to do this. The shaft size will be =
1/4"

Thanks!
Bailey--

waterproof shaft seal?
 

Thanks for the tips. I should have provided more detail but it will
basically be a fractional horse low depth propulsion (similar to a
trolling motor only much smaller). In taking a trolling motor apart,
the water seal looks like nothing but an "O" ring or grommet next to
the bushing. How complicated can that be? Surely there has to be
something available to accomplish this.

waterproof shaft seal?
 

I think it's called a trolling motor ....
DF
"MBS" wrote in message
om...
Thanks for the tips. I should have provided more detail but it will
basically be a fractional horse low depth propulsion (similar to a
trolling motor only much smaller). In taking a trolling motor apart,
the water seal looks like nothing but an "O" ring or grommet next to
the bushing. How complicated can that be? Surely there has to be
something available to accomplish this.

waterproof shaft seal?
 

DF,
I made reference to "much smaller" than a trolling motor. How then is
this a conventional trolling motor?

waterproof shaft seal?
 

On 14 Nov 2003 08:46:58 -0800, (MBS) wrote:

I am trying to waterproof a small electric motor (submerged) so that
shaft will be sticking out of waterproof enclosure. Can anyone point
me to a source of water sealed bushings or bearings for this sort of
application? I have been looking all over the net and can't seem to
come up with ideas or supplies to do this. The shaft size will be =
1/4"

Thanks!
Bailey--

I passed your request several times - this is not a topic for
beginners to lightly undertake - but what the hell.
Go to a bearing distributors (look in the phone book)
Ask what shaft seals they have in 1/4 inch.
Pick a likely candidate, and find some tube that will fit the outer
diameter of the seal.
Place three in series in the housing, and fix the housing on the motor
in some waterproof way. This will put you in with a chance.

Brian W Altus OK
p.s. The seals go with the lip facing *outwards*

waterproof shaft seal?
 

Sorry, missed that ...
If it's that small, I'd be looking at magnetic drive. Try looking for
magnetic drive pumps.
David
"MBS" wrote in message
om...
DF,
I made reference to "much smaller" than a trolling motor. How then is
this a conventional trolling motor?

waterproof shaft seal?