Propeller Shaft Vibration
 

Melton,
Sounds like you need to check the Alignment with boat in the water. Your
hull is probably taking a different set in the water than when it on the
stands

Sounds like he needs Mike. broom handle and Channel-loks doesn't it
Frank.

htmp
http://midistudio.com/midi/Carroll/SummerWind.mid

http://community.webtv.net/tassail/ThomJazz
/html

Propeller Shaft Vibration
 

"Thom Stewart" wrote in message
...
Melton,
Sounds like you need to check the Alignment with boat in the water. Your
hull is probably taking a different set in the water than when it on the
stands

Sounds like he needs Mike. broom handle and Channel-loks doesn't it
Frank.

htmp
http://midistudio.com/midi/Carroll/SummerWind.mid

http://community.webtv.net/tassail/ThomJazz
/html


Found to much play in the cutlass bearing. Replaced it and everything is
fine.

Propeller Shaft Vibration
 

Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

Propeller Shaft Vibration
 

Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

Propeller Shaft Vibration
 

Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

Propeller Shaft Vibration
 

On Feb 3, 2:09 am, (Thom Stewart) wrote:
Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

text_html_part
1KDownload

No Kidding Thom, what kind of dip**** pulls and mic's a
shaft..balances a prop and does not check or replace the cutlass?


Joe

Propeller Shaft Vibration
 

On Feb 3, 9:09 am, Charlie Morgan wrote:
On 3 Feb 2007 06:04:29 -0800, "Joe" wrote:

On Feb 3, 2:09 am, (Thom Stewart) wrote:
Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

text_html_part
1KDownload

No Kidding Thom, what kind of dip**** pulls and mic's a
shaft..balances a prop and does not check or replace the cutlass?

Joe

If either of you dumbasses could read, you would know that he didn't pull the
shaft.

CWM

You're a ****ing idiot BB.
Lets review what he wrote.......ready..........OK

checked the shaft for straightness
without removing it, reinstalled the prop and took the boat out
again.
Same vibration, so I had it pulled again and took the shaft and prop
in for a check. Dyno balance on the prop A-ok, the shaft was true and
passed static balance no problem.

Now bonehead, how did he take it in for a check without removing it?

Joe

Propeller Shaft Vibration
 

"Joe" wrote in message
ps.com...
On Feb 3, 9:09 am, Charlie Morgan wrote:
On 3 Feb 2007 06:04:29 -0800, "Joe" wrote:

On Feb 3, 2:09 am, (Thom Stewart) wrote:
Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

text_html_part
1KDownload

No Kidding Thom, what kind of dip**** pulls and mic's a
shaft..balances a prop and does not check or replace the cutlass?

Joe

If either of you dumbasses could read, you would know that he didn't pull
the
shaft.

CWM

You're a ****ing idiot BB.
Lets review what he wrote.......ready..........OK

checked the shaft for straightness
without removing it, reinstalled the prop and took the boat out
again.
Same vibration, so I had it pulled again and took the shaft and prop
in for a check. Dyno balance on the prop A-ok, the shaft was true and
passed static balance no problem.

Now bonehead, how did he take it in for a check without removing it?

Joe


Given enough time Mr. Morgan will figure it out.

JB

Propeller Shaft Vibration
 

On Feb 3, 11:24 am, "John Birch" wrote:
"Joe" wrote in message

ps.com...





On Feb 3, 9:09 am, Charlie Morgan wrote:
On 3 Feb 2007 06:04:29 -0800, "Joe" wrote:

On Feb 3, 2:09 am, (Thom Stewart) wrote:
Come off it Melton,

You removed the Shaft and never checked the Cutlas Bearing? Spare me.

text_html_part
1KDownload

No Kidding Thom, what kind of dip**** pulls and mic's a
shaft..balances a prop and does not check or replace the cutlass?

Joe

If either of you dumbasses could read, you would know that he didn't pull
the
shaft.

CWM

You're a ****ing idiot BB.
Lets review what he wrote.......ready..........OK

checked the shaft for straightness
without removing it, reinstalled the prop and took the boat out
again.
Same vibration, so I had it pulled again and took the shaft and prop
in for a check. Dyno balance on the prop A-ok, the shaft was true and
passed static balance no problem.

Now bonehead, how did he take it in for a check without removing it?

Joe

Given enough time Mr. Morgan will figure it out.

JB- Hide quoted text -

- Show quoted text -

I doubt it..... he studied at Harvard.

Joe

Propeller Shaft Vibration
 

John Birch wrote:
"Joe" wrote in message
ps.com...
On Feb 3, 9:09 am, Charlie Morgan wrote:
On 3 Feb 2007 06:04:29 -0800, "Joe" wrote:

On Feb 3, 2:09 am, (Thom Stewart) wrote:
Come off it Melton,
You removed the Shaft and never checked the Cutlas Bearing? Spare me.
text_html_part
1KDownload
No Kidding Thom, what kind of dip**** pulls and mic's a
shaft..balances a prop and does not check or replace the cutlass?
Joe
If either of you dumbasses could read, you would know that he didn't pull
the
shaft.

CWM
You're a ****ing idiot BB.
Lets review what he wrote.......ready..........OK

checked the shaft for straightness
without removing it, reinstalled the prop and took the boat out
again.
Same vibration, so I had it pulled again and took the shaft and prop
in for a check. Dyno balance on the prop A-ok, the shaft was true and
passed static balance no problem.

Now bonehead, how did he take it in for a check without removing it?

Joe


Given enough time Mr. Morgan will figure it out.

Doubtful. Now that RB has left, he's the simpleton of the group.