Home |
Search |
Today's Posts |
|
#1
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]()
Wow... so a friend and I moved my boat from its old home to the new location
yesterday. Wednesday was nice and sunny, but Thursday started with light fog that turned into a steady rain. The visibility was very good for distances of up to about two miles, but then dropped off pretty quickly due to the fog and rain. Some other background info... We were in the deep mostly commercial channel that connects the two marinas, in the center outbound lane, so about 1/3 the distance across from right to left. There are many big ships moored on the commercial docks, some being loaded or refitted, others that will probably never sail again. There are multiple small channels off the main channel. The main channel is fairly busy with commercial traffic, mostly tugs pushing or pulling barges, not including hosting several large marinas, the biggest of which has 500+ craft. The main channel is also fairly narrow especially at the main turn. Most power boats (non-commercial) with relatively shallow drafts and big engines tend to go on the wrong side of the inbound lane (not saying it's right, but that's what they do) to avoid the slower outboat sailboats. (I suppose this is better than them screaming by with large wakes.) The turning area (where the channel makes a sharp turn and where the truly big ships berth) is perhaps 100 yards wide, although the big ships would certainly not be near the edges. Anyway, we headed out of the marina, crossed the inland turn part of the channel, and were in the middle of the outbound lane, just past the turn. There's a huge, rusting liberty ship side-tied right at the corner and past that a very small side channel. As we made a fairly deep turn to start out the main channel, I noticed that there was a tug on side-tie to a barge heading in, approximately 1 mile ahead of us. This thing was huge. It looked huge even that far away, and was proceeding quite slowly inbound. I felt we had plenty of time to make the deep turn, then get back in line on my side of the channel, which is what we did. We were doing about 5 kts. Sails down, just engine. I finished the turn, then started to come back to "center" on my side. The liberty ship was being passed on my starboard, so that would mean I had a bit more room on the inside of the channel in case the incoming tug/barge needed the room... not sure if he was going to turn behind us to the left or side-tie the barge ahead of us. Just as I passed the liberty ship and was nearly across the side channel just past her bow, a push tug came lumbering out of the side channel right for us! We're talking 100 maybe 120 feet off our starboard side just stern of the shrouds and really moving. At this point the incoming tub/barge is a lot closer, perhaps 1000 yards, but even worse, another tug is in front of them (not related to them) coming down toward us with the intention it looked like of going into yet another one of the small channels, thus was coming down the outbound lane. He was slightly more to the center of the channel, perhaps 300 yards ahead and moving pretty well. Since I didn't see them previously, must have come out of another side channel. (They do this a lot.) The guy in the enclosed bridge (way high up from our perspective) wasn't even looking in our direction. No way to turn away without getting in the way of the oncoming traffic. Obviously, I couldn't hold my course and speed. Over his engines, I'm sure he couldn't have heard a horn, and there was no time to hail him. My friend was waving, but he wasn't looking. So, I figured the only thing to do was to try and throttle up, hoping I could stay ahead of him long enough for him to see us. At this point the oncoming tub that I hadn't see before saw us and started to back, sensing that this was not a good situation. We were unable to out-run the push barge, but I did slow the rate of his approach a bit. 10-15 seconds into it, the driver suddenly snapped his head in our direction (he was practically directly astern of us, so I'm still not sure what he was looking at while he was driving), then throttled way, way down, and the situation was resolved. I think the other tug must have hailed him or he saw us out of the corner of his eye. He finally acknowledged my friend's wave, but he looked pretty harassed at that point. I normally would have said "something" to him directly, but it was really starting to rain, and we just wanted to get done with it. I can't imagine the damage had he hit us with one of those huge vertical bumpers. -- "j" ganz @@ www.sailnow.com |
#2
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]() Capt. JG wrote: Wow... so a friend and I moved my boat from its old home to the new location yesterday. Wednesday was nice and sunny, but Thursday started with light fog that turned into a steady rain. The visibility was very good for distances of up to about two miles, but then dropped off pretty quickly due to the fog and rain. Some other background info... We were in the deep mostly commercial channel that connects the two marinas, in the center outbound lane, so about 1/3 the distance across from right to left. There are many big ships moored on the commercial docks, some being loaded or refitted, others that will probably never sail again. There are multiple small channels off the main channel. The main channel is fairly busy with commercial traffic, mostly tugs pushing or pulling barges, not including hosting several large marinas, the biggest of which has 500+ craft. The main channel is also fairly narrow especially at the main turn. Most power boats (non-commercial) with relatively shallow drafts and big engines tend to go on the wrong side of the inbound lane (not saying it's right, but that's what they do) to avoid the slower outboat sailboats. (I suppose this is better than them screaming by with large wakes.) The turning area (where the channel makes a sharp turn and where the truly big ships berth) is perhaps 100 yards wide, although the big ships would certainly not be near the edges. Anyway, we headed out of the marina, crossed the inland turn part of the channel, and were in the middle of the outbound lane, just past the turn. There's a huge, rusting liberty ship side-tied right at the corner and past that a very small side channel. As we made a fairly deep turn to start out the main channel, I noticed that there was a tug on side-tie to a barge heading in, approximately 1 mile ahead of us. This thing was huge. It looked huge even that far away, and was proceeding quite slowly inbound. I felt we had plenty of time to make the deep turn, then get back in line on my side of the channel, which is what we did. We were doing about 5 kts. Sails down, just engine. I finished the turn, then started to come back to "center" on my side. The liberty ship was being passed on my starboard, so that would mean I had a bit more room on the inside of the channel in case the incoming tug/barge needed the room... not sure if he was going to turn behind us to the left or side-tie the barge ahead of us. Just as I passed the liberty ship and was nearly across the side channel just past her bow, a push tug came lumbering out of the side channel right for us! We're talking 100 maybe 120 feet off our starboard side just stern of the shrouds and really moving. At this point the incoming tub/barge is a lot closer, perhaps 1000 yards, but even worse, another tug is in front of them (not related to them) coming down toward us with the intention it looked like of going into yet another one of the small channels, thus was coming down the outbound lane. He was slightly more to the center of the channel, perhaps 300 yards ahead and moving pretty well. Since I didn't see them previously, must have come out of another side channel. (They do this a lot.) The guy in the enclosed bridge (way high up from our perspective) wasn't even looking in our direction. No way to turn away without getting in the way of the oncoming traffic. Obviously, I couldn't hold my course and speed. Over his engines, I'm sure he couldn't have heard a horn, and there was no time to hail him. My friend was waving, but he wasn't looking. So, I figured the only thing to do was to try and throttle up, hoping I could stay ahead of him long enough for him to see us. At this point the oncoming tub that I hadn't see before saw us and started to back, sensing that this was not a good situation. We were unable to out-run the push barge, but I did slow the rate of his approach a bit. 10-15 seconds into it, the driver suddenly snapped his head in our direction (he was practically directly astern of us, so I'm still not sure what he was looking at while he was driving), then throttled way, way down, and the situation was resolved. I think the other tug must have hailed him or he saw us out of the corner of his eye. He finally acknowledged my friend's wave, but he looked pretty harassed at that point. I normally would have said "something" to him directly, but it was really starting to rain, and we just wanted to get done with it. I can't imagine the damage had he hit us with one of those huge vertical bumpers. Close call. I don't know the full circumstances, but this might be an example of a situation in which the Mac, with its large engine and shallow draft, could outmaneuver the oncoming traffic. Jim |
#3
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]()
"JimC" wrote in message
t... Capt. JG wrote: Wow... so a friend and I moved my boat from its old home to the new location yesterday. Wednesday was nice and sunny, but Thursday started with light fog that turned into a steady rain. The visibility was very good for distances of up to about two miles, but then dropped off pretty quickly due to the fog and rain. Some other background info... We were in the deep mostly commercial channel that connects the two marinas, in the center outbound lane, so about 1/3 the distance across from right to left. There are many big ships moored on the commercial docks, some being loaded or refitted, others that will probably never sail again. There are multiple small channels off the main channel. The main channel is fairly busy with commercial traffic, mostly tugs pushing or pulling barges, not including hosting several large marinas, the biggest of which has 500+ craft. The main channel is also fairly narrow especially at the main turn. Most power boats (non-commercial) with relatively shallow drafts and big engines tend to go on the wrong side of the inbound lane (not saying it's right, but that's what they do) to avoid the slower outboat sailboats. (I suppose this is better than them screaming by with large wakes.) The turning area (where the channel makes a sharp turn and where the truly big ships berth) is perhaps 100 yards wide, although the big ships would certainly not be near the edges. Anyway, we headed out of the marina, crossed the inland turn part of the channel, and were in the middle of the outbound lane, just past the turn. There's a huge, rusting liberty ship side-tied right at the corner and past that a very small side channel. As we made a fairly deep turn to start out the main channel, I noticed that there was a tug on side-tie to a barge heading in, approximately 1 mile ahead of us. This thing was huge. It looked huge even that far away, and was proceeding quite slowly inbound. I felt we had plenty of time to make the deep turn, then get back in line on my side of the channel, which is what we did. We were doing about 5 kts. Sails down, just engine. I finished the turn, then started to come back to "center" on my side. The liberty ship was being passed on my starboard, so that would mean I had a bit more room on the inside of the channel in case the incoming tug/barge needed the room... not sure if he was going to turn behind us to the left or side-tie the barge ahead of us. Just as I passed the liberty ship and was nearly across the side channel just past her bow, a push tug came lumbering out of the side channel right for us! We're talking 100 maybe 120 feet off our starboard side just stern of the shrouds and really moving. At this point the incoming tub/barge is a lot closer, perhaps 1000 yards, but even worse, another tug is in front of them (not related to them) coming down toward us with the intention it looked like of going into yet another one of the small channels, thus was coming down the outbound lane. He was slightly more to the center of the channel, perhaps 300 yards ahead and moving pretty well. Since I didn't see them previously, must have come out of another side channel. (They do this a lot.) The guy in the enclosed bridge (way high up from our perspective) wasn't even looking in our direction. No way to turn away without getting in the way of the oncoming traffic. Obviously, I couldn't hold my course and speed. Over his engines, I'm sure he couldn't have heard a horn, and there was no time to hail him. My friend was waving, but he wasn't looking. So, I figured the only thing to do was to try and throttle up, hoping I could stay ahead of him long enough for him to see us. At this point the oncoming tub that I hadn't see before saw us and started to back, sensing that this was not a good situation. We were unable to out-run the push barge, but I did slow the rate of his approach a bit. 10-15 seconds into it, the driver suddenly snapped his head in our direction (he was practically directly astern of us, so I'm still not sure what he was looking at while he was driving), then throttled way, way down, and the situation was resolved. I think the other tug must have hailed him or he saw us out of the corner of his eye. He finally acknowledged my friend's wave, but he looked pretty harassed at that point. I normally would have said "something" to him directly, but it was really starting to rain, and we just wanted to get done with it. I can't imagine the damage had he hit us with one of those huge vertical bumpers. Close call. I don't know the full circumstances, but this might be an example of a situation in which the Mac, with its large engine and shallow draft, could outmaneuver the oncoming traffic. Jim What would the shallow draft have to do with it? -- "j" ganz @@ www.sailnow.com |
#4
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]() Capt. JG wrote: "JimC" wrote in message t... Capt. JG wrote: Wow... so a friend and I moved my boat from its old home to the new location yesterday. Wednesday was nice and sunny, but Thursday started with light fog that turned into a steady rain. The visibility was very good for distances of up to about two miles, but then dropped off pretty quickly due to the fog and rain. Some other background info... We were in the deep mostly commercial channel that connects the two marinas, in the center outbound lane, so about 1/3 the distance across from right to left. There are many big ships moored on the commercial docks, some being loaded or refitted, others that will probably never sail again. There are multiple small channels off the main channel. The main channel is fairly busy with commercial traffic, mostly tugs pushing or pulling barges, not including hosting several large marinas, the biggest of which has 500+ craft. The main channel is also fairly narrow especially at the main turn. Most power boats (non-commercial) with relatively shallow drafts and big engines tend to go on the wrong side of the inbound lane (not saying it's right, but that's what they do) to avoid the slower outboat sailboats. (I suppose this is better than them screaming by with large wakes.) The turning area (where the channel makes a sharp turn and where the truly big ships berth) is perhaps 100 yards wide, although the big ships would certainly not be near the edges. Anyway, we headed out of the marina, crossed the inland turn part of the channel, and were in the middle of the outbound lane, just past the turn. There's a huge, rusting liberty ship side-tied right at the corner and past that a very small side channel. As we made a fairly deep turn to start out the main channel, I noticed that there was a tug on side-tie to a barge heading in, approximately 1 mile ahead of us. This thing was huge. It looked huge even that far away, and was proceeding quite slowly inbound. I felt we had plenty of time to make the deep turn, then get back in line on my side of the channel, which is what we did. We were doing about 5 kts. Sails down, just engine. I finished the turn, then started to come back to "center" on my side. The liberty ship was being passed on my starboard, so that would mean I had a bit more room on the inside of the channel in case the incoming tug/barge needed the room... not sure if he was going to turn behind us to the left or side-tie the barge ahead of us. Just as I passed the liberty ship and was nearly across the side channel just past her bow, a push tug came lumbering out of the side channel right for us! We're talking 100 maybe 120 feet off our starboard side just stern of the shrouds and really moving. At this point the incoming tub/barge is a lot closer, perhaps 1000 yards, but even worse, another tug is in front of them (not related to them) coming down toward us with the intention it looked like of going into yet another one of the small channels, thus was coming down the outbound lane. He was slightly more to the center of the channel, perhaps 300 yards ahead and moving pretty well. Since I didn't see them previously, must have come out of another side channel. (They do this a lot.) The guy in the enclosed bridge (way high up from our perspective) wasn't even looking in our direction. No way to turn away without getting in the way of the oncoming traffic. Obviously, I couldn't hold my course and speed. Over his engines, I'm sure he couldn't have heard a horn, and there was no time to hail him. My friend was waving, but he wasn't looking. So, I figured the only thing to do was to try and throttle up, hoping I could stay ahead of him long enough for him to see us. At this point the oncoming tub that I hadn't see before saw us and started to back, sensing that this was not a good situation. We were unable to out-run the push barge, but I did slow the rate of his approach a bit. 10-15 seconds into it, the driver suddenly snapped his head in our direction (he was practically directly astern of us, so I'm still not sure what he was looking at while he was driving), then throttled way, way down, and the situation was resolved. I think the other tug must have hailed him or he saw us out of the corner of his eye. He finally acknowledged my friend's wave, but he looked pretty harassed at that point. I normally would have said "something" to him directly, but it was really starting to rain, and we just wanted to get done with it. I can't imagine the damage had he hit us with one of those huge vertical bumpers. Close call. I don't know the full circumstances, but this might be an example of a situation in which the Mac, with its large engine and shallow draft, could outmaneuver the oncoming traffic. Jim What would the shallow draft have to do with it? Because if you have a 1.5-ft draft (with the dagger board pulled up), you don't have to worry so much about staying in a channel (between the red and green markers, or whatever). - You can temporarily pull over a few feet outside the channel to a shallower portion of the waterway out of the way of larger vessels with deeper drafts. As I said, I don't know the exact layout of the situation you were in, so it may or may not have been a factor in your situation. (Once more, it may or may not have been a factor in your situation.) - But in some cases, larger boats are limited to a marked channel or to sections of a waterway deep enough for their deeper draft, whereas a shallow-draft boat can maneuver through shallower sections and thereby skirt around or otherwise avoid deep-draft boats heading down a channel. Or, it can simply edge along slowly for a few minutes outside the channel until the other boats are gone. - Not the safest thing to do, but if it gets you out of the way of a large, fast boat that doesn't see you, it may be better than getting run over. Jim |
#5
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]()
"JimC" wrote in message
. net... What would the shallow draft have to do with it? Because if you have a 1.5-ft draft (with the dagger board pulled up), you don't have to worry so much about staying in a channel (between the red and green markers, or whatever). - You can temporarily pull over a few feet outside the channel to a shallower portion of the waterway out of the way of larger vessels with deeper drafts. As I said, I don't know the exact layout of the situation you were in, so it may or may not have been a factor in your situation. (Once more, it may or may not have been a factor in your situation.) - But in some cases, larger boats are limited to a marked channel or to sections of a waterway deep enough for their deeper draft, whereas a shallow-draft boat can maneuver through shallower sections and thereby skirt around or otherwise avoid deep-draft boats heading down a channel. Or, it can simply edge along slowly for a few minutes outside the channel until the other boats are gone. - Not the safest thing to do, but if it gets you out of the way of a large, fast boat that doesn't see you, it may be better than getting run over. Jim Why would I have my dagger board pulled up in storm conditions? -- "j" ganz @@ www.sailnow.com |
#6
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]() Capt. JG wrote: "JimC" wrote in message . net... What would the shallow draft have to do with it? Because if you have a 1.5-ft draft (with the dagger board pulled up), you don't have to worry so much about staying in a channel (between the red and green markers, or whatever). - You can temporarily pull over a few feet outside the channel to a shallower portion of the waterway out of the way of larger vessels with deeper drafts. As I said, I don't know the exact layout of the situation you were in, so it may or may not have been a factor in your situation. (Once more, it may or may not have been a factor in your situation.) - But in some cases, larger boats are limited to a marked channel or to sections of a waterway deep enough for their deeper draft, whereas a shallow-draft boat can maneuver through shallower sections and thereby skirt around or otherwise avoid deep-draft boats heading down a channel. Or, it can simply edge along slowly for a few minutes outside the channel until the other boats are gone. - Not the safest thing to do, but if it gets you out of the way of a large, fast boat that doesn't see you, it may be better than getting run over. Jim Why would I have my dagger board pulled up in storm conditions? In my case, there are multiple choices. - Dagger board all the way down (5.5-ft draft), all the way up (1.5-ft draft), or anything in between. If I had been in your situation, as understood, I would have had the board partially down, providing perhaps 3 ft of draft, which provides control of the boat at displacement speeds but which would also permit it to to be temporarily maneuvered into shallower waters out of the path of oncoming, deeper draft vessels. Alternatively, one could rely on the speeds available with the large motor to get out of their way. My point is that options are available that wouldn't be available with a conventional, fixed-keel, hull-speed-limited vessel. Jim |
#7
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]() "JimC" wrote in message t... this might be an example of a situation in which the Mac, with its flimsy construction and crappy hull desiegn, would have kept you safe and sound, still tied to the dock.. Jim |
#8
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]()
"Scotty" wrote in message
. .. "JimC" wrote in message t... this might be an example of a situation in which the Mac, with its flimsy construction and crappy hull desiegn, would have kept you safe and sound, still tied to the dock.. Jim Jim's right. I should never have left the dock. -- "j" ganz @@ www.sailnow.com |
#9
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]() "Capt. JG" wrote in message ... "Scotty" wrote in message . .. "JimC" wrote in message t... this might be an example of a situation in which the Mac, with its flimsy construction and crappy hull desiegn, would have kept you safe and sound, still tied to the dock.. Jim Jim's right. I should never have left the dock. Not without at least a 70 HP motor. |
#10
![]()
posted to alt.sailing.asa
|
|||
|
|||
![]()
"Scotty" wrote in message
... "Capt. JG" wrote in message ... "Scotty" wrote in message . .. "JimC" wrote in message t... this might be an example of a situation in which the Mac, with its flimsy construction and crappy hull desiegn, would have kept you safe and sound, still tied to the dock.. Jim Jim's right. I should never have left the dock. Not without at least a 70 HP motor. Yeah, I guess my wimpy 13 hp just doesn't cut it. -- "j" ganz @@ www.sailnow.com |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Forum | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
Fresh Water Tank | Cruising |