|If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.|
||Thread Tools||Display Modes|
SPIN-TEC ROLLER FURLER
Spin-Tec Roller Furlers are found at http://www.clrmarine.com/572.html
The new standard in roller furling systems
Our Triumph 2000 was engineered by sailors, for sailors. With no ball
bearings or complicated mechanisms to bind or fail, furling the sail
around the forestay is its only job.
Our system stands alone instead of being under constant stress from
heavy tension loads. The components are only under the compression
loads imparted by luff tension. There is virtually no friction or
resistance to furling. There is no possibility of halyard wrap because
the halyard is removed after the sail is hoisted. And there are no
bearing hang-ups from over-tensioned sails.
Other systems may look good when new, but after just a few years in a
marine environment they have literally rotted away. With Spin-Tec's
roller furling systems, all dissimilar metals are completely isolated
ensuring there will be no corrosion between the various components of
the system insuring long product life.
The Difference? Superior Engineering
Spin-Tec's roller furling systems have a number of key features and
benefits not found in many other systems on the market.
With a simplified design, there are no complex / moving parts to bind
or fail! As a result, the system requires no maintenance. No more
worrying about washing off / rinsing out your furling system after
Race/Cruise with ease
With the R/C 1000 it is simple to use either your racing or your
cruising sails without modifications to either the sails or the
furler. When cruising, tack your sail to the upper bail on the drum
and furl your sail. When racing, tack your sail to the lower bail and
use the foil as a racing foil. It's that simple!
No ball bearings!
The system has no ball bearings. Instead large Delrin bushings are
used in the lower assembly and smaller Delrin bushings are used
throughout each of the foil sections. System friction is near zero and
furling couldn't be easier. Bushing loads are minimal for low wear and
resistance. Lastly, Delrin bushings require no maintenance!
No halyard swivel!
The furling systems have no halyard swivel or ball bearing assemblies
(this is the device typically used at the top of the forestay to carry
the load of the sail hoist, separate the halyard from the turning sail
foil and reduce the possibility of halyard wrap). When using our
roller furling system, the halyard is removed from the sail after it
has been hoisted eliminating added weight and the need for a swivel
No Opportunities for Corrosion Between Dissimilar Metals
The furlers have complete isolation of all dissimilar metals to
prevent corrosion. They utilize West System® Epoxy to isolate the
stainless steel drum from the aluminum foil sections.
Large Stainless Steel Furling Drum
Spin-Tec's furling systems includes a large 4" diameter drum to give
you maximum power/torque when furling your sail. The drum is
completely open (so you can easily deal with a riding turn should one
occur). Ever seen an aluminum roller furling drum after several
season's of use? You'll love our Stainless Steel Furling Drum that's
designed to survive the harsh marine environment.
The system is simple to install and comes complete with everything you
will need for installation including furling line and lead blocks.
There is nothing else to purchase and many of our customers do their
Don't want to install it yourself?
All units come with an Lifetime Warranty. The simple design and robust
materials allow us to offer a lifetime warranty that's tough to beat!
The Lifetime Warranty
Spin-Tec Equipment Company's Roller Furling Devices are fully
warranted against defects in materials or workmanship to the original
owner for life. If our products fail, we will repair or replace them,
at our option, without charge.
Suitable proof of purchase must be presented at the time a claim is
made, and a return authorization number must be obtained from the
factory prior to returning products.
Spin-Tec Equipment Company shall not be liable for any personal
injury, property damage, or any special, incidental or consequential
damages of any kind resulting from defects in or malfunctions of its
Some states or countries do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to
state or country to country.
Customer Satisfaction Guarantee
Anytime you buy a Spin-Tec product, you have the right to use it for
60 days from date of purchase to determine whether it is satisfactory
and that you want to keep it. If you are not completely satisfied,
obtain a return authorization number and then return it to the
original place of purchase for a full refund of the purchase price.
This guarantee does not apply to products which have been
intentionally damaged or misused.
Spin-Tec Equipment Company Pledge of Fairness
If, after you have decided to keep the product, you find it does not
give the services you expected, please contact us. We will extend
every effort to make a fair adjustment in accordance with the terms of
this Satisfaction Guarantee.
|Thread||Thread Starter||Forum||Replies||Last Post|
|Things are starting to spin up||Joe||ASA||6||August 18th 07 10:33 PM|
|Roller furling versus roller reefing||Scott||General||9||August 15th 05 02:19 PM|
|Open or Spin?||SoFarrell||General||19||April 6th 05 04:11 AM|
|Prop spin generator||marklan||General||10||August 11th 04 01:52 AM|
|Wally's Spin||Bobsprit||ASA||11||May 13th 04 10:44 PM|