Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #11   Report Post  
Keith
 
Posts: n/a
Default Dinghy tow line

Lucky you! You can find that stuff at Home Depot for next to nothing, since
it's not labeled "marine"!

--


Keith
__
The light at the end of the tunnel has been turned off due to budget cuts.
"Gerald Atkin" wrote in message
...
What is the best line for towing a dinghy?

I have seen somewhere on the net a multifilament polypropylene dinghy tow
rope that looks a lot like braided line but it is poly and floats. Assume
this would be good. But can't seem to find it. If I recall it was yellow
with a red thread,

Jerry



  #12   Report Post  
Matt Koch
 
Posts: n/a
Default Dinghy tow line


"Russ Barron" wrote in message
news
On Wed, 12 May 2004 10:56:49 -0400, dbraun wrote:

SNIP I took to leading the
line over a fender lashed flat near the stern cleat to reduce the shock
loads in rough weather.


What a great idea. Thanks

Matt


  #13   Report Post  
rhys
 
Posts: n/a
Default Dinghy tow line

On Wed, 12 May 2004 17:31:21 -0400, Rodney Myrvaagnes
wrote:



Yes, that is why I said "less likely." I have seen dinghy painters
with a series of floats, that might make it "even less likely."
However, hauling the dinghy up short against the stern before going in
reverse is still a great idea.

I have a rough idea of the distance between my prop and the tender's
D-ring in a straight line, and a tad shorter than that is my standard
"deployment".

If it's choppy, I let off 20 feet or so. If it's light air in a
current, you can sometimes have under sail the slightly humiliating
vista of seeing your tender passing your sailboat. This is your cue to
switch on the motor or retire below for "recreation".

BTW, the fender as shock absorber idea is great. That's why I love NGs
like this...someone's solved problems you've yet to consider or
discover.

R.

  #14   Report Post  
Keith
 
Posts: n/a
Default Dinghy tow line

I rigged my towline up from a suggestion I received earlier. There are
actually two lines, both three straid laid nylon. I used this for the shock
absorbing characteristics. The first line is about 50', and has a thimble
spliced into both ends. One gets shackled to the dink. Then I have another
line with an eye spliced into one end. I hook this onto my cleat/hawsepipe
on the starboard side, pass the line through the thimble of the tow rope,
then pass it through the cleat/hawsepipe on the port side. This allows me to
adjust the length of the entire assembly to get the dink to where it wants
to run based on the wake and bow wave ( I have a trawler that runs around 7
knots). If I need to cinch it up for docking or whatever, I just pull in the
bitter end of the cleat line until the towline is reachable, then grab it
and pull it up close and cleat it off.

Another suggestion that I haven't done yet is to make a towline that splits
into two, with eyes spliced into two ends to pass over the tubes at the reat
of the dink, then forward to attach to the towline, or spliced together. The
idea behind this is to prevent a towing eye from pulling out of the dink and
losing it.

--


Keith
__
A pessimist's blood type is always b-negative.
"rhys" wrote in message
...
On Wed, 12 May 2004 17:31:21 -0400, Rodney Myrvaagnes
wrote:



Yes, that is why I said "less likely." I have seen dinghy painters
with a series of floats, that might make it "even less likely."
However, hauling the dinghy up short against the stern before going in
reverse is still a great idea.

I have a rough idea of the distance between my prop and the tender's
D-ring in a straight line, and a tad shorter than that is my standard
"deployment".

If it's choppy, I let off 20 feet or so. If it's light air in a
current, you can sometimes have under sail the slightly humiliating
vista of seeing your tender passing your sailboat. This is your cue to
switch on the motor or retire below for "recreation".

BTW, the fender as shock absorber idea is great. That's why I love NGs
like this...someone's solved problems you've yet to consider or
discover.

R.



  #15   Report Post  
Lew Hodgett
 
Posts: n/a
Default Dinghy tow line

Gerald Atkin writes:

What is the best line for towing a dinghy?


Go to K-Mart, buy a water ski tow rope.

It will float, it's cheap, and it does the job.


--
Lew

S/A: Challenge, The Bullet Proof Boat, (Under Construction in the Southland)
Visit: http://home.earthlink.net/~lewhodgett for Pictures




  #16   Report Post  
Ed
 
Posts: n/a
Default Dinghy tow line

Depends on what you call a dingy.

For my small inflatable in calm water, I use Poly... easy to splice,
cheap, will last for years if you get it out of the sun after use.

For my tender (18' whaler)in rough water, I use 5/8" nylon with a VERY
long bridle (40') and another 60' of tow line. Great stretch for
rougher seas. I shorten it at the tender end if needed so that the long
bridle stays intact for stabilty and a more straight pull. (Tested to
22 kts in 3-5' seas, 17 kts in 5-7' seas) When pulling into port, we
do shorten it on the tow boat end and go down to towing on the non-slip
side cleat.

My neighbor calls a 31 jupiter his "dingy" He uses a 3/4" Multibraid
with a similar setup to my Whaler.

Funny thing.... the ONLY time I ever got the line caught up in the
wheels was when I was towing the little guy with the floating line.
(had to cut it loose in 1000+ ft of water... you tend to be VERY careful
with heavy diameter nylon...)





Gerald Atkin wrote:
What is the best line for towing a dinghy?

I have seen somewhere on the net a multifilament polypropylene dinghy tow
rope that looks a lot like braided line but it is poly and floats. Assume
this would be good. But can't seem to find it. If I recall it was yellow
with a red thread,

Jerry


  #17   Report Post  
Larry Bradley
 
Posts: n/a
Default Dinghy tow line

I know this is late, but I just got back from a few weeks on the boat.

I have a heavy fibreglass 8' dinghy. I use "Marstron" (brand name, I
assume) - it is the flexible braided polyprop line such as others have
described. Mine has been in use for 15 years and shows no signs of
deteriorating in the sunlight. But I'm replacing it this week with a
new one, just in case.

I use a rubber mooring line snubber (the kind with loops in the ends,
rather than the kind that you twist your mooring line around) in the
towing line right at the dinghy - it takes up the shock loads, and if
it tries to stretch too much, the part of the painter that "bypasses"
the snubber takes the load.

I've also just started playing with a trick I saw on another boat.
There is a short line (with the snubber) from the dinghy to a small
block. This block rides on a piece of line (Marstron) that runs from
the port stern cleat to the startboard. This line is rather short
(barely reaches the water).

When we are towing the dinghy under power, it is up close, and rides
in the center behind the boat, rather than off to one side. The block
lets it easily move around if the wave/wind conditions move it.

Only used it briefly - not sure if it is going to be any better than
just towing close behind. But it LOOKS cool!

Larry Bradley
C&C Corvette 31 "Lady Di"
Kingston, ON, Canada

Gerald Atkin wrote:

What is the best line for towing a dinghy?

I have seen somewhere on the net a multifilament polypropylene dinghy tow
rope that looks a lot like braided line but it is poly and floats. Assume
this would be good. But can't seem to find it. If I recall it was yellow
with a red thread,

Jerry


Larry Bradley VE3CRX
Remove "removeme" from my e-mail address for direct mail
Ottawa, Canada

(use the e-mail address above to send directly to me)
  #18   Report Post  
Makani
 
Posts: n/a
Default Dinghy tow line

This might be another option.

http://www.shockles.com/usage/dinghy-towing.cfm

"Larry Bradley" wrote in message ...
I know this is late, but I just got back from a few weeks on the boat.

I have a heavy fibreglass 8' dinghy. I use "Marstron" (brand name, I
assume) - it is the flexible braided polyprop line such as others have
described. Mine has been in use for 15 years and shows no signs of
deteriorating in the sunlight. But I'm replacing it this week with a
new one, just in case.

I use a rubber mooring line snubber (the kind with loops in the ends,
rather than the kind that you twist your mooring line around) in the
towing line right at the dinghy - it takes up the shock loads, and if
it tries to stretch too much, the part of the painter that "bypasses"
the snubber takes the load.

I've also just started playing with a trick I saw on another boat.
There is a short line (with the snubber) from the dinghy to a small
block. This block rides on a piece of line (Marstron) that runs from
the port stern cleat to the startboard. This line is rather short
(barely reaches the water).

When we are towing the dinghy under power, it is up close, and rides
in the center behind the boat, rather than off to one side. The block
lets it easily move around if the wave/wind conditions move it.

Only used it briefly - not sure if it is going to be any better than
just towing close behind. But it LOOKS cool!

Larry Bradley
C&C Corvette 31 "Lady Di"
Kingston, ON, Canada

Gerald Atkin wrote:

What is the best line for towing a dinghy?

I have seen somewhere on the net a multifilament polypropylene dinghy tow
rope that looks a lot like braided line but it is poly and floats. Assume
this would be good. But can't seem to find it. If I recall it was yellow
with a red thread,

Jerry


Larry Bradley VE3CRX
Remove "removeme" from my e-mail address for direct mail
Ottawa, Canada

(use the e-mail address above to send directly to me)
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
collapsible dinghy Parallax Boat Building 1 May 9th 04 05:24 PM
Birthdate of Norman Maclean Harry Krause General 1 December 24th 03 01:05 AM
Skull Creek Marina complaint Aaron Cruising 8 October 14th 03 08:33 PM
What's the best dinghy for cruising and why? Harvey Porter Cruising 15 August 22nd 03 01:37 AM
Fuel pump to carbs fuel line replacement Bob General 5 July 29th 03 05:51 PM


All times are GMT +1. The time now is 09:46 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017