Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
 
Posts: n/a
Default painting a fiberglass dinghy

i just find a little sailing dinghy , but the hull is need to repaint
,what is the best way to go to repaint the hull outside?
epoxy paint ? and what kind of prep . need to be done to get a nice
luster ? sound very basic but i can use some good advice.

  #2   Report Post  
Jonathan W.
 
Posts: n/a
Default painting a fiberglass dinghy

A smooth shiny finish is primarily the function of good prep work. If
the hull has been painted before, it needs to be sanded so that all the
gloss is gone from the original paint, and all the dings and divots have
been filled with a sandable filling material, either polyester like
Bondo, or epoxy like West System with mircoballons. Sand, fill, sand
fill what didn't quite fill the first time and sand again. If you use a
fairing primer like Interlux 244 it will further help achieve the
"perfect" finish, but any enamel properly brushed out should give you a
fine, serviceable finish.

In any event, read the manufacturers directions and thin properly. A
capful of the right brushing liquid (Interlux 333?) can make the
difference between an OK finish and one that has people saying, "How'd
you do that?"

Your basic starter sanding grit might be 80 grit paper, finish off with
at least 220 prior to painting.

Good luck,

Jonathan

wrote:
i just find a little sailing dinghy , but the hull is need to repaint
,what is the best way to go to repaint the hull outside?
epoxy paint ? and what kind of prep . need to be done to get a nice
luster ? sound very basic but i can use some good advice.



--
I am building my daughter an Argie 10 sailing dinghy, check it out:
http://home.comcast.net/~jonsailr
  #3   Report Post  
seawitch
 
Posts: n/a
Default painting a fiberglass dinghy

thank you very much it will help a lot , will send you pics. ,how is
turned out

  #4   Report Post  
MMC
 
Posts: n/a
Default painting a fiberglass dinghy

May want to also check compatability of the new paint with the old. Wet a
rag with the solvent for the new paint and place on the old paint. If the 2
paints are compatable the solvent will not lift the old paint.
MMC
"Jonathan W." wrote in message
...
A smooth shiny finish is primarily the function of good prep work. If
the hull has been painted before, it needs to be sanded so that all the
gloss is gone from the original paint, and all the dings and divots have
been filled with a sandable filling material, either polyester like
Bondo, or epoxy like West System with mircoballons. Sand, fill, sand
fill what didn't quite fill the first time and sand again. If you use a
fairing primer like Interlux 244 it will further help achieve the
"perfect" finish, but any enamel properly brushed out should give you a
fine, serviceable finish.

In any event, read the manufacturers directions and thin properly. A
capful of the right brushing liquid (Interlux 333?) can make the
difference between an OK finish and one that has people saying, "How'd
you do that?"

Your basic starter sanding grit might be 80 grit paper, finish off with
at least 220 prior to painting.

Good luck,

Jonathan

wrote:
i just find a little sailing dinghy , but the hull is need to repaint
,what is the best way to go to repaint the hull outside?
epoxy paint ? and what kind of prep . need to be done to get a nice
luster ? sound very basic but i can use some good advice.



--
I am building my daughter an Argie 10 sailing dinghy, check it out:
http://home.comcast.net/~jonsailr



  #5   Report Post  
seawitch
 
Posts: n/a
Default painting a fiberglass dinghy

i just looked a bit closer , this dinghy of mine was never painted just
dull and scratched up , i wonder would be way to save the original coat
just "bring it up" and feather in the scratch with epoxy ? what you all
think?



  #6   Report Post  
Jonathan W.
 
Posts: n/a
Default painting a fiberglass dinghy

The original gelcoat is the surface of choice. Once you paint, you start
a maintenance cycle.

Davis makes a product called, I believe, Fiberglass Stain Remover, which
is essentially oxalic (sp?) acid in a jelly base that does a great job
of cleaning up stained fiberglass.

Use that, and follow up with one of the many mild polishing compounds
(perhaps someone will pipe up with brand recommendations) then wax, and
you should be able to get it looking almost good as new.

Unless the scratches go through the gelcoat, you might want to wait and
see what they look like after stain removal before playing with fillers.
It is incredibly hard to match white surfaces and you may find you draw
more attention to the "scratch" by trying to fix it than leaving it
mostly alone.

You might also look at the Sailnet.com website. The store is defunct,
but they are leaving the web pages up, along with a store of 1,500 or so
articles, many of which are on maintenance of different boat surfaces, etc.

Have fun,

Jonathan

seawitch wrote:

i just looked a bit closer , this dinghy of mine was never painted just
dull and scratched up , i wonder would be way to save the original coat
just "bring it up" and feather in the scratch with epoxy ? what you all
think?



--
I am building my daughter an Argie 10 sailing dinghy, check it out:
http://home.comcast.net/~jonsailr
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Cleaning Fiberglass Rick Cruising 19 October 21st 05 07:13 PM
rec.boats.paddle sea kayaking FAQ [email protected] General 0 October 19th 05 05:38 AM
What is the Right Size Motor for a 17-Ft Fiberglass Boat? [email protected] General 10 October 19th 05 12:54 AM
Fiberglass loss of strength Mic Cruising 1 October 15th 05 08:03 PM
Stowing Dinghy on Pacific Seacraft 34 db9 Cruising 13 October 14th 05 06:18 PM


All times are GMT +1. The time now is 01:25 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017